收藏本站
参数资料
型号： KSZ8842-16MVL
厂商： Micrel Inc
文件页数： 82/141页
文件大小： 0K
描述： IC ETHERNET SW 2PORT BUS 128LQFP
标准包装： 90
控制器类型： 以太网开关控制器
接口： PCI
电源电压： 3.1 V ~ 3.5 V
工作温度： 0°C ~ 70°C
安装类型： 表面贴装
封装/外壳： 128-LQFP
供应商设备封装： 128-LQFP（14x14）
包装： 托盘
产品目录页面： 1081 (CN2011-ZH PDF)
配用： 576-1635-ND - BOARD EVALUATION KSZ8842-16MVL
其它名称： 576-2119
KSZ8842-16MVL-ND
Micrel, Inc.
KSZ8842-16/32 MQL/MVL/MVLI/MBL
October 2007
45
M9999-102207-1.9
IGMP Support
For Internet Group Management Protocol (IGMP) support in Layer 2, the KSZ8842M provides two components:
“IGMP” Snooping
The KSZ8842M traps IGMP packets and forwards them only to the processor (host port). The IGMP packets are
identified as IP packets (either Ethernet IP packets, or IEEE 802.3 SNAP IP packets) with IP version = 0x4 and protocol
version number = 0x2.
“Multicast Address Insertion” in the Static MAC Table
Once the multicast address is programmed in the Static MAC Table, the multicast session is trimmed to the subscribed
ports, instead of broadcasting to all ports.
IPv6 MLD Snooping
The KSZ8842M traps IPv6 Multicast Listener Discovery (MLD) packets and forwards them only to the processor (host
port). MLD snooping is controlled by SGCR2[13] (MLD snooping enable) and SGCR2[12] (MLD option).
Setting SGCR2[13] causes the KSZ8842M to trap packets that meet all of the following conditions:
IPv6 multicast packets
Hop count limit = 1
IPv6 next header = 1 or 58 (or = 0 with hop-by-hop next header = 1 or 58)
If SGCR2[12] = 1, IPv6 next header = 43, 44, 50, 51, or 60 (or =0 with hop-by-hop next header = 43, 44, 50, 51,
or 60)
Port Mirroring Support
KSZ8842M supports “Port Mirroring” comprehensively as:
“receive only” mirror on a port
All the packets received on the port are mirrored on the sniffer port. For example, port 1 is programmed to be “receive
sniff” and the host port is programmed to be the “sniffer port”. A packet received on port 1 is destined to port 2 after the
internal lookup. The KSZ8842M forwards the packet to both port 2 and the host port. The KSZ8842M can optionally even
forward “bad” received packets to the “sniffer port”.
“transmit only” mirror on a port
All the packets transmitted on the port are mirrored on the sniffer port. For example, port 1 is programmed to be “transmit
sniff” and the host port is programmed to be the “sniffer port”. A packet received on port 2 is destined to port 1 after the
internal lookup. The KSZ8842M forwards the packet to both port 1 and the host port.
“receive and transmit” mirror on two ports
All the packets received on port A and transmitted on port B are mirrored on the sniffer port. To turn on the “AND” feature,
set register SGCR2, bit 8 to “1”. For example, port 1 is programmed to be “receive sniff”, port 2 is programmed to be
“transmit sniff”, and the host port is programmed to be the “sniffer port”. A packet received on port 1 is destined to port 2
after the internal lookup. The KSZ8842M forwards the packet to both port 2 and the host port.
Multiple ports can be selected as “receive sniff” or “transmit sniff”. In addition, any port can be selected as the “sniffer
port”. All these per port features can be selected through registers P1CR2, P2CR2, and P3CR2 for ports 1, 2, and the
host port, respectively.
IEEE 802.1Q VLAN Support
The KSZ8842M supports 16 active VLANs out of the 4096 possible VLANs specified in the IEEE 802.1Q specification.
KSZ8842M provides a 16-entry VLAN table, which converts the 12-bits VLAN ID (VID) to the 4-bits Filter ID (FID) for
address lookup. If a non-tagged or null-VID-tagged packet is received, the ingress port default VID is used for lookup. In
VLAN mode, the lookup process starts with VLAN table lookup to determine whether the VID is valid. If the VID is not
valid, the packet is dropped and its address is not learned. If the VID is valid, the FID is retrieved for further lookup. The
FID + Destination Address (FID+DA) are used to determine the destination port. The FID + Source Address (FID+SA) are
used for address learning. (See Tables 10 and 11.)
相关PDF资料
PDF描述
V300A12C400BL3 CONVERTER MOD DC/DC 12V 400W
PIC16F687-E/P IC PIC MCU FLASH 2KX14 20DIP
V300A12C400B3 CONVERTER MOD DC/DC 12V 400W
V300A12C400B2 CONVERTER MOD DC/DC 12V 400W
PIC16C505T-04E/SL IC MCU OTP 1KX12 14SOIC
相关代理商/技术参数
参数描述
KSZ8842-16MVL TR 功能描述:以太网 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ8842-16MVL-EVAL 功能描述:BOARD EVALUATION KSZ8842-16MVL RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- 主要目的:电源管理，电池充电器 嵌入式:否 已用 IC / 零件:MAX8903A 主要属性:1 芯锂离子电池 次要属性:状态 LED 已供物品:板
KSZ8842-16MVLI 功能描述:以太网 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ8842-16MVLI TR 功能描述:以太网 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray
KSZ8842-32 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*