- 您现在的位置：买卖IC网 > PDF目录11576 > KSZ8873MLL AM TR (Micrel Inc)IC ETHERNET SWITCH 3PORT 64LQFP PDF资料下载
参数资料
| 型号： | KSZ8873MLL AM TR |
| 厂商： | Micrel Inc |
| 文件页数： | 29/115页 |
| 文件大小： | 0K |
| 描述： | IC ETHERNET SWITCH 3PORT 64LQFP |
| 产品培训模块： | KSZ8873 Ethernet Switches |
| 标准包装： | 1,000 |
| 控制器类型： | 以太网开关控制器 |
| 接口： | MII |
| 电源电压： | 1.8V，2.5V，3.3V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-PQFP（10x10） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页
Micrel, Inc.
KSZ8873MLL/FLL/RLL
September 20, 2013
20
Revision 1.6
100BASE-FX Operation
100BASE-FX operation is similar to 100BASE-TX operation with the differences being that the scrambler/de-scrambler
and MLT3 encoder/decoder are bypassed on transmission and reception. In addition, auto-negotiation is bypassed and
auto MDI/MDI-X is disabled.
100BASE-FX Signal Detection
In 100BASE-FX operation, FXSD (fiber signal detect), input Pins 15 and 63, is usually connected to the fiber transceiver
SD (signal detect) output pin. The fiber signal threshold can be selected by Register 192 bit 7 and 6 respectively for port 2
and port 1, When FXSD is less than the threshold, no fiber signal is detected and a far-end fault (FEF) is generated.
When FXSD is over the threshold, the fiber signal is detected.
Alternatively, the designer may choose not to implement the FEF feature. In this case, the FXSD input pin is tied high to
force 100BASE-FX mode.
100BASE-FX signal detection is summarized in Table 1:
Table 1. FX Signal Threshold
Register 192 bit 7 (port 2), bit 6 (port 1)
Fiber Signal Threshold at FXSD
1
2.0V
0
1.2V
To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver SD output voltage
swing to match the FXSD pin’s input voltage threshold.
100BASE-FX Far-End Fault
A far-end fault (FEF) occurs when the signal detection is logically false on the receive side of the fiber transceiver. The
KSZ8873FLL detects a FEF when its FXSD input is Fiber Signal Threshold. When a FEF is detected, the KSZ8873FLL
signals its fiber link partner that a FEF has occurred by sending 84 1’s followed by a zero in the idle period between
frames.
By default, FEF is enabled. FEF can be disabled through register setting.
10BASE-T Transmit
The 10BASE-T driver is incorporated with the 100BASE-TX driver to allow for transmission using the same magnetics.
They are internally wave-shaped and pre-emphasized into outputs with a typical 2.3V amplitude. The harmonic contents
are at least 27dB below the fundamental frequency when driven by an all-ones Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffers and level detecting squelch circuits are employed. A differential input receiver circuit and
a phase-locked loop (PLL) perform the decoding function. The Manchester-encoded data stream is separated into clock
signal and NRZ data. A squelch circuit rejects signals with levels less than 400mV or with short pulse widths to prevent
noise at the RXP-or-RXM input from falsely triggering the decoder. When the input exceeds the squelch limit, the PLL
locks onto the incoming signal and the KSZ8873MLL/FLL/RLL decodes a data frame. The receiver clock is maintained
active during idle periods in between data reception.
MDI/MDI-X Auto Crossover
To eliminate the need for crossover cables between similar devices, the KSZ8873MLL/FLL/RLL supports HP Auto
MDI/MDI-X and IEEE 802.3u standard MDI/MDI-X auto crossover. HP Auto MDI/MDI-X is the default.
The auto-sense function detects remote transmit and receive pairs and correctly assigns transmit and receive pairs for the
KSZ8873MLL/FLL/RLL device. This feature is extremely useful when end users are unaware of cable types, and also,
saves on an additional uplink configuration connection. The auto-crossover feature can be disabled through the port
control registers, or MIIM PHY registers.
相关PDF资料 |
PDF描述 |
|---|---|
| PIC16C54CT-04I/SO | IC MCU OTP 512X12 18SOIC |
| PIC12CE519T-04I/SN | IC MCU OTP 1KX12 W/EE 8SOIC |
| V300A8C400BG | CONVERTER MOD DC/DC 8V 400W |
| LTC1955IUH#PBF | IC SMART CARD INTERFACE DL 32QFN |
| V300A8C400BF3 | CONVERTER MOD DC/DC 8V 400W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8873MLL-EVAL | 功能描述:以太网开发工具 3-Port Fast Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8873MLLI | 功能描述:以太网 IC 3-Port Fast Ethernet Switch with 1x RMII Interface (Industrial Grade, Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8873MLLJ | 功能描述:以太网 IC 3-Port Fast Ethernet Switch with 1x RMII Interface (Extended Temp) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8873MML | 功能描述:以太网 IC 3-Port Fast Ethernet Switch with 2x MII Interface, Lead Free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8873MML-EVAL | 功能描述:以太网开发工具 3-Port Fast Ethernet Switch with 2x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。