参数资料
| 型号： | KSZ8997 |
| 厂商： | Micrel Inc |
| 文件页数： | 11/39页 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 10/100 8PORT 128PQFP |
| 标准包装： | 66 |
| 系列： | * |
| 类型： | * |
| 应用： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 128-BFQFP |
| 供应商设备封装： | 128-PQFP（14x20） |
| 包装： | 托盘 |
| 产品目录页面： | 1081 (CN2011-ZH PDF) |
| 其它名称： | 576-1043 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页
Micrel, Inc.
KS8997/KSZ8997
February 2007
19
M9999-022807-1.1
Programmable Features
Priority Schemes
The KS8997 can determine priority through three different means at the ingress point. The first method is a simple
per port method, the second is via the 802.1p frame tag and the third is by viewing the DSCP (TOS) field in the IPv4
header. Of course for the priority to be effective, the high and low priority queues must be enabled on the destination
port or egress point.
Per Port Method
General priority can be specified on a per port basis. In this type of priority all traffic from the specified input port is
considered high priority in the destination queue. This can be useful in IP phone applications mixed with other data
types of traffic where the IP phone connects to a specific port. The IP phone traffic would be high priority (outbound)
to the wide area network. The inbound traffic to the IP phone is all of the same priority to the IP phone.
802.1p Method
This method works well when used with ports that have mixed data and media flows. The inbound port examines the
priority field in the tag and determines the high or low priority. Priority profiles are setup in the Priority Classification
Control in the “EEPROM Memory Map” section.
IPv4 DSCP Method
This is another per frame way of determining outbound priority. The DSCP (Differentiated Services Code Point–
RFC#2474) method uses the TOS field in the IP header to determine high and low priority on a per code point basis.
Each fully decoded code point can have either a high or low priority. A larger spectrum of priority flows can be
defined with this larger code space.
More specific to implementation, the most significant 6 bits of the TOS field are fully decoded into 64 possibilities,
and the singular code that results is compared against the corresponding bit in the DSCP register. If the register bit is
a 1, the priority is high and if 0, the priority is low.
Other Priority Considerations
When setting up the priority scheme, one should consider other available controls to regulate the traffic. One of these
is Priority Control Scheme (register 2 bits 2-3) which controls the interleaving of high and low priority frames. Options
allow from a 2:1 ratio up to a setting that sends all the high priority first. This setting controls all ports globally.
Another global feature is Priority Buffer Reserve (register 2 bit 1). If this is set, there is a 6KB (10%) buffer dedicated
to high priority traffic, otherwise if cleared the buffer is shared between all traffic.
On an individual port basis there are controls that enable DSCP, 802.1p, port based and high/low priority queues.
These are contained in registers 4-11 bits 5-3 and 0. It should be noted that there is a special pin that generally
enables the 802.1p priority for all ports (pin 60). When this pin is active (high) all ports will have the 802.1p priority
enabled unless specifically disabled by EEPROM programming (bit 4 of registers 4-11). Default high priority is a
value of '100' and above in the VLAN tag with low priority being a value of '011' and below.
相关PDF资料 |
PDF描述 |
|---|---|
| KSZ8995FQI | IC SWITCH 10/100 5PORT 128-PQFP |
| AD9970BCPZ | IC PROCESSOR CCD SIGNAL 32LFCSP |
| ADP5587ACPZ-R7 | IC EXPANDER/KEYBOARD CTRLR |
| LFXP3E-4TN144C | IC FPGA 3.1KLUTS 100I/O 144-TQFP |
| LFXP3C-4TN144C | IC FPGA 3.1KLUTS 100I/O 144-TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ8999 | 功能描述:以太网 IC 8 Port 10/100 Switch plus MII with PHY and Frame Buffers (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ8999-EVAL | 功能描述:以太网开发工具 KSZ8999 Evaluation Board RoHS:否 制造商:Micrel 产品:Evaluation Boards 类型:Ethernet Transceivers 工具用于评估:KSZ8873RLL 接口类型:RMII 工作电源电压: |
| KSZ8999-EVAL | 制造商:Micrel Inc 功能描述:BOARD EVALUATION FOR KSZ8999 |
| KSZ8999I | 功能描述:以太网 IC 8 Port 10/100 Switch plus MII with PHY and Frame Buffers I-temp (Lead Free) RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ9021GN | 功能描述:以太网 IC Gigabit Ethernet Transceiver with GMII/MII, Lead Free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。