- 您现在的位置：买卖IC网 > PDF目录10791 > KSZ9021GNI (Micrel Inc)TXRX GIG ETH GMII/MII 64-QFN PDF资料下载
参数资料
| 型号： | KSZ9021GNI |
| 厂商： | Micrel Inc |
| 文件页数： | 10/53页 |
| 文件大小： | 0K |
| 描述： | TXRX GIG ETH GMII/MII 64-QFN |
| 标准包装： | 348 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 8/8 |
| 规程： | 千兆位以太网 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘 |
| 供应商设备封装： | 64-QFN（8x8） |
| 包装： | 托盘 |
| 配用： | 576-3873-ND - BOARD EVALUATION FOR KSZ9021GN |
| 其它名称： | 576-3789 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
Micrel, Inc.
KSZ9021GN
September 2010
18
M9999-091010-1.1
Timing Recovery Circuit
In 1000Base-T mode, the mixed-signal clock recovery circuit together with the digital phase locked loop is used to
recover and track the incoming timing information from the received data. The digital phase locked loop has very low
long-term jitter to maximize the signal-to-noise ratio of the receive signal.
The 1000Base-T slave PHY is required to transmit the exact receive clock frequency recovered from the received data
back to the 1000Base-T master PHY. Otherwise, the master and slave will not be synchronized after long transmission.
Additionally, this helps to facilitate echo cancellation and NEXT removal.
Adaptive Equalizer
In 1000Base-T mode, the adaptive equalizer provides the following functions:
Detection for partial response signaling
Removal of NEXT and ECHO noise
Channel equalization
Signal quality is degraded by residual echo that is not removed by the analog hybrid and echo due to impedance
mismatch. The KSZ9021GN employs a digital echo canceller to further reduce echo components on the receive signal.
In 1000Base-T mode, data transmission and reception occurs simultaneously on all four pairs of wires (four channels).
This results in high frequency cross-talk coming from adjacent wires. The KSZ9021GN employs three NEXT cancellers
on each receive channel to minimize the cross-talk induced by the other three channels.
In 10Base-T/100Base-TX mode, the adaptive equalizer needs only to remove the inter-symbol interference and recover
the channel loss from the incoming data.
Trellis Encoder and Decoder
In 1000Base-T mode, the transmitted 8-bit data is scrambled into 9-bit symbols and further encoded into 4D-PAM5
symbols. The initial scrambler seed is determined by the specific PHY address to reduce EMI when more than one
KSZ9021GN are used on the same board. On the receiving side, the idle stream is examined first. The scrambler seed,
pair skew, pair order and polarity have to be resolved through the logic. The incoming 4D-PAM5 data is then converted
into 9-bit symbols and then de-scrambled into 8-bit data.
Functional Description: Additional 10/100/1000 PHY Features
Auto MDI/MDI-X
The Automatic MDI/MDI-X feature eliminates the need to determine whether to use a straight cable or a crossover cable
between the KSZ9021GN and its link partner. This auto-sense function detects the MDI/MDI-X pair mapping from the
link partner, and then assigns the MDI/MDI-X pair mapping of the KSZ9021GN accordingly.
The following table shows the KSZ9021GN 10/100/1000 pin-out assignments for MDI/MDI-X pin mapping.
MDI
MDI-X
Pin (RJ-45 pair)
1000Base-T
100Base-TX
10Base-T
1000Base-T
100Base-TX
10Base-T
TXRXP/M_A (1,2)
A+/-
TX+/-
B+/-
RX+/-
TXRXP/M_B (3,6)
B+/-
RX+/-
A+/-
TX+/-
TXRXP/M_C (4,5)
C+/-
Not used
D+/-
Not used
TXRXP/M_D (7,8)
D+/-
Not used
C+/-
Not used
Table 1. MDI / MDI-X Pin Mapping
Auto MDI/MDI-X is enabled by default. It is disabled by writing a one to register 28 (1Ch) bit 6. MDI and MDI-X mode is
set by register 28 (1Ch) bit 7 if auto MDI/MDI-X is disabled.
An isolation transformer with symmetrical transmit and receive data paths is recommended to support auto MDI/MDI-X.
相关PDF资料 |
PDF描述 |
|---|---|
| CMP04FSZ | IC COMPARATOR QUAD LP 14-SOIC |
| LTC1387CG#PBF | IC TXRX RS232/RS485 5VSNGL20SSOP |
| LT1134AISW#PBF | IC 4DRV/4RCV RS232 5V 24-SOIC |
| ADCMP565BPZ | IC COMP DUAL ULTRA-FAST 20-PLCC |
| LTC1321CSW#PBF | IC TXRX RS232/485/EIA562 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KSZ9021GQ | 功能描述:以太网 IC Gigabit Ethernet Transceiver with GMII/MII, Lead Free RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ9021GQI | 功能描述:以太网 IC Gigabit Ethernet Transceiver w/ GMII/MII, I-Temp RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ9021RL | 功能描述:以太网 IC Gigabit Ethernet Transceiver with GMII RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
| KSZ9021RL-EVAL | 制造商:Micrel Inc 功能描述:GIGABIT ETHERNET TRANSCEIVER W 制造商:Micrel Inc 功能描述:KIT EVALUATION FOR KSZ9021RL |
| KSZ9021RLI | 功能描述:以太网 IC Gigabit Ethernet Transceiver with RGMII, I-Temp RoHS:否 制造商:Micrel 产品:Ethernet Switches 收发器数量:2 数据速率:10 Mb/s, 100 Mb/s 电源电压-最大:1.25 V, 3.45 V 电源电压-最小:1.15 V, 3.15 V 最大工作温度:+ 85 C 封装 / 箱体:QFN-64 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。