- 您现在的位置：买卖IC网 > PDF目录262391 > KW025A0Y41-BZ 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | KW025A0Y41-BZ |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 45 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT |
| 文件页数： | 4/24页 |
| 文件大小： | 2376K |
| 代理商： | KW025A0Y41-BZ |
Preliminary Data Sheet
March 24, 2006
KW010/015/020/025 Series Power Modules:
36 – 75Vdc Input; 1.0 to 5.0Vdc Output; 10 to 25A Output current
Tyco Electronics Power Systems
12
Test Configurations
Design Considerations
Input Filtering
TO OSCILLOSCOPE
CURRENT PROBE
LTEST
12μH
B
A
TTE
R
Y
CS
220μF
E.S.R.<0.1
Ω
@ 20°C 100kHz
33μF
Vin+
Vin-
NOTE: Measure input reflected ripple current with a simulated
source inductance (LTEST) of 12μH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
The power module should be connected to a low
ac-impedance source. Highly inductive source
impedance can affect the stability of the power
module. For the test configuration in Figure 37 a 33μF
electrolytic capacitor (ESR<0.1
Ω at 100kHz),
mounted close to the power module helps ensure the
stability of the unit. Consult the factory for further
application guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and
separation requirements of the end-use safety agency
standard, i.e., UL 60950-1-3, CSA C22.2 No. 60950-
00, and VDE 0805:2001-12 (IEC60950-1).
Figure 37. Input Reflected Ripple Current Test
Setup.
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
VO(+)
V O(–)
RESISTIVE
LOAD
SCOPE
COPPER STRIP
GROUND PLANE
10uF
0.1uF
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75Vdc), for the module’s output to be considered as
meeting the requirements for safety extra-low voltage
(SELV), all of the following must be true:
The input source is to be provided with reinforced
insulation from any other hazardous voltages,
including the ac mains.
One VIN pin and one VOUT pin are to be
grounded, or both the input and output pins are
to be kept floating.
Figure 38. Output Ripple and Noise Test Setup.
The input pins of the module are not operator
accessible.
Another SELV reliability test is conducted on the
whole system (combination of supply source and
subject module), as required by the safety
agencies, to verify that under a single fault,
hazardous voltages do not appear at the
module’s output.
Vout+
Vout-
Vin+
Vin-
RLOAD
Rcontact
Rdistribution
Rcontact
Rdistribution
Rcontact
Rdistribution
VIN
VO
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Note:
Do not ground either of the input pins of the
module without grounding one of the output
pins. This may allow a non-SELV voltage to
appear between the output pins and ground.
The power module has extra-low voltage (ELV)
outputs when all inputs are ELV.
All flammable materials used in the manufacturing of
these modules are rated 94V-0, or tested to the
UL60950 A.2 for reduced thickness.
Figure 39. Output Voltage and Efficiency Test
Setup.
For input voltages exceeding –60 Vdc but less than or
equal to –75 Vdc, these converters have been
evaluated to the applicable requirements of BASIC
INSULATION between secondary DC MAINS
DISTRIBUTION input (classified as TNV-2 in Europe)
and unearthed SELV outputs (-B option only).
η =
VO.IO
VIN.IIN
x 100 %
Efficiency
The input to these units is to be provided with a
maximum 5 A time-delay fuse in the ungrounded lead.
相关PDF资料 |
PDF描述 |
|---|---|
| KAP12AFF | SILICON, RECTIFIER DIODE |
| KAP12DFF | SILICON, RECTIFIER DIODE |
| KAP12FCF | 3 PHASE, SILICON, RECTIFIER DIODE |
| KAP24ALF | SILICON, RECTIFIER DIODE |
| KAP24CCF | SILICON, RECTIFIER DIODE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KW025A0Y41-SRZ | 功能描述:DC/DC转换器 48Vin 1.8Vout 25A SMT RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| KW025A0Y41Z | 功能描述:DC/DC转换器 48Vin 1.8Vout 25A TH RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| KW025A0Y641Z | 制造商:LINEAGEPOWER 制造商全称:LINEAGEPOWER 功能描述:36 - 75Vdc Input; 1.2 to 5.0Vdc Output; 10 to 25A Output current |
| KW103G2 | 功能描述:THERMISTOR NTC 10K OHM +/-0.50 C RoHS:否 类别:传感器，转换器 >> 热敏电阻 - NTC 系列:KW 标准包装:100 系列:* |
| KW103J2 | 功能描述:NTC THERMISTOR 10K OHM 0.5C BEAD 制造商:us sensor/littelfuse inc 系列:KW 包装:散装 零件状态:在售 25°C 时欧姆阻值:10k 电阻容差:±0.5°C B 值容差:- B0/50:3892K B25/50:- B25/75:- B25/85:- B25/100:- 工作温度:120°C 功率 - 最大值:30mW 长度 - 引线:1.50"（38.00mm） 安装类型:自由悬挂 封装/外壳:圆珠，环氧树脂 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。