- 您现在的位置：买卖IC网 > Datasheet目录467 > KXTF9-4100 (Kionix Inc)IC ACCELEROMETER TRI-AXIS 10-LGA Datasheet资料下载
参数资料
| 型号： | KXTF9-4100 |
| 厂商： | Kionix Inc |
| 文件页数： | 13/49页 |
| 文件大小： | 0K |
| 描述： | IC ACCELEROMETER TRI-AXIS 10-LGA |
| 应用说明： | Sensor Handling, Mounting, Soldering KXTF9 Getting Started |
| 标准包装： | 1 |
| 系列： | KXTF9 |
| 轴： | X，Y，Z |
| 加速范围： | ±2g，4g，8g |
| 灵敏度： | 64计数/g，32计数/g，16计数/g（8位，1024计数/g，512计数/g，256计数/g（12位） |
| 电源电压： | * |
| 输出类型： | 数字 - I²C |
| 带宽： | 400Hz |
| 接口： | I²C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-VFLGA |
| 供应商设备封装： | 10-LGA（3x3） |
| 其它名称： | 1191-1001-6 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
PART NUMBER:
± 2g / 4g / 8g Tri-axis Digital
Accelerometer Specifications
KXTF9-4100
Rev. 6
Jun-2011
It is mandatory that receiving devices acknowledge (ACK) each transaction. Therefore, the transmitter must
release the SDA line during this ACK pulse. The receiver then pulls the data line low so that it remains stable
low during the high period of the ACK clock pulse. A receiver that has been addressed, whether it is Master or
Slave, is obliged to generate an ACK after each byte of data has been received. To conclude a transaction,
the Master must transmit a stop condition (P) by transitioning the SDA line from low to high while SCL is high.
The I 2 C bus is now free.
Writing to a KXTF9 8-bit Register
Upon power up, the Master must write to the KXTF9’s control registers to set its operational mode. Therefore,
when writing to a control register on the I 2 C bus, as shown Sequence 1 on the following page, the following
protocol must be observed: After a start condition, SAD+W transmission, and the KXTF9 ACK has been
returned, an 8-bit Register Address (RA) command is transmitted by the Master. This command is telling the
KXTF9 to which 8-bit register the Master will be writing the data. Since this is I 2 C mode, the MSB of the RA
command should always be zero (0). The KXTF9 acknowledges the RA and the Master transmits the data to
be stored in the 8-bit register. The KXTF9 acknowledges that it has received the data and the Master
transmits a stop condition (P) to end the data transfer. The data sent to the KXTF9 is now stored in the
appropriate register. The KXTF9 automatically increments the received RA commands and, therefore,
multiple bytes of data can be written to sequential registers after each Slave ACK as shown in Sequence 2 on
the following page.
Reading from a KXTF9 8-bit Register
When reading data from a KXTF9 8-bit register on the I 2 C bus, as shown in Sequence 3 on the next page, the
following protocol must be observed: The Master first transmits a start condition (S) and the appropriate Slave
Address (SAD) with the LSB set at ‘0’ to write. The KXTF9 acknowledges and the Master transmits the 8 -bit
RA of the register it wants to read. The KXTF9 again acknowledges, and the Master transmits a repeated
start condition (Sr). After the repeated start condition, the Master addresses the KXTF9 with a ‘1’ in the LSB
(SAD+R) to read from the previously selected register. The Slave then acknowledges and transmits the data
from the requested register. The Master does not acknowledge (NACK) it received the transmitted data, but
transmits a stop condition to end the data transfer. Note that the KXTF9 automatically increments through its
sequential registers, allowing data to be read from multiple registers following a single SAD+R command as
shown below in Sequence 4 on the following page.
If a receiver cannot transmit or receive another complete byte of data until it has performed some other
function, it can hold SCL low to force the transmitter into a wait state. Data transfer only continues when the
receiver is ready for another byte and releases SCL.
36 Thornwood Dr. – Ithaca, NY 14850
tel: 607-257-1080 – fax:607-257-1146
www.kionix.com - info@kionix.com
? 2010 Kionix – All Rights Reserved
425-2397-1106241613
Page 13 of 49
相关PDF资料 |
PDF描述 |
|---|---|
| L01Z050S05 | SENSOR CURRENT 50A 5V BI MOD |
| L05Z800S15 | SENSOR CURRENT |
| L06P800S05 | SENSOR CURRENT +/-800A +5V |
| L12P025D15 | SENSOR CURRENT +/-25A +/-15V |
| L18P060D15 | SENSOR CURRENT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| KX-TG2208B | 制造商:Panasonic Industrial Company 功能描述:TELEPHONE |
| KX-TG2511ET | 制造商:Panasonic Industrial Company 功能描述:Single DECT Phone KX-TG2511 (UK) |
| KX-TG2512ET | 制造商:Panasonic Industrial Company 功能描述:Twin DECT Phone KX-TG2512 (UK) |
| KX-TGA10 | 制造商:Panasonic Industrial Company 功能描述:COVER |
| KXTGA420B/EX | 制造商:Panasonic Industrial Company 功能描述:OTC TELEPHONE |
发布紧急采购，3分钟左右您将得到回复。