- 您现在的位置：买卖IC网 > PDF目录17725 > L2K110BJ224KB-T (Taiyo Yuden)CAP ARRAY 2CH 0.22UF 10V 0504 PDF资料下载
参数资料
| 型号： | L2K110BJ224KB-T |
| 厂商： | Taiyo Yuden |
| 文件页数： | 16/16页 |
| 文件大小： | 0K |
| 描述： | CAP ARRAY 2CH 0.22UF 10V 0504 |
| 产品变化通告： | X5R, X7R Part Number Change |
| 标准包装： | 10 |
| 电容： | 0.22µF |
| 电压 - 额定： | 10V |
| 电介质材料： | 陶瓷 |
| 电容器数量： | 2 |
| 电路类型： | 隔离 |
| 温度系数： | X5R |
| 容差： | ±10% |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 0504（1210 公制） |
| 尺寸/尺寸： | 0.054" L x 0.039" W（1.37mm x 1.00mm） |
| 高度 - 座高（最大）： | 0.024"（0.60mm） |
| 包装： | 剪切带 (CT) |
| 其它名称： | 587-1037-1 |
■ PRECAUTIONS
Precautions on the use of Multilayer Ceramic Capacitors
5. Cleaning
Precautions
Technical
consider-
ations
◆ Cleaning conditions
1. When PCBs are cleaned after capacitors mounting, please select the appropriate cleaning solution in accordance with the intended use of the cleaning. （ e.g. to
remove soldering ?ux or other materials from the production process. ）
2. Cleaning condition shall be determined after it is veri?ed by using actual cleaning machine that the cleaning process does not affect capacitor's characteristics.
1. The use of inappropriate cleaning solutions can cause foreign substances such as ?ux residue to adhere to capacitors or deteriorate their outer coating, resulting in
a degradation of the capacitor's electrical properties （ especially insulation resistance ） .
2. Inappropriate cleaning conditions （ insuf?cient or excessive cleaning ） may adversely affect the performance of the capacitors.
In the case of ultrasonic cleaning, too much power output can cause excessive vibration of PCBs which may lead to the cracking of capacitors or the soldered
portion, or decrease the terminal electrodes' strength. Therefore, the following conditions shall be carefully checked;
Ultrasonic output : 20 W/ ? or less
Ultrasonic frequency : 40 kHz or less
Ultrasonic washing period : 5 min. or less
6. Resin coating and mold
1. With some type of resins, decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while left under normal stor-
age conditions resulting in the deterioration of the capacitor's performance.
Precautions
2. When a resin's hardening temperature is higher than capacitor's operating temperature, the stresses generated by the excessive heat may lead to damage or
destruction of capacitors.
The use of such resins, molding materials etc. is not recommended.
7. Handling
◆ Splitting of PCB
1. When PCBs are split after components mounting, care shall be taken so as not to give any stresses of de?ection or twisting to the board.
2. Board separation shall not be done manually, but by using the appropriate devices.
Precautions
◆ Mechanical considerations
Be careful not to subject capacitors to excessive mechanical shocks.
（ 1 ） If ceramic capacitors are dropped onto a ?oor or a hard surface, they shall not be used.
（ 2 ） Please be careful that the mounted components do not come in contact with or bump against other boards or components.
8. Storage conditions
◆ Storage
1. To maintain the solderability of terminal electrodes and to keep packaging materials in good condition, care must be taken to control temperature and humidity in
the storage area. Humidity should especially be kept as low as possible.
? Recommended conditions
Ambient temperature : Below 30 ℃
Precautions
Technical
consider-
ations
Humidity : Below 70% RH
The ambient temperature must be kept below 40 ℃ . Even under ideal storage conditions, solderability of capacitor is deteriorated as time passes, so capaci-
tors shall be used within 6 months from the time of delivery.
? Ceramic chip capacitors shall be kept where no chlorine or sulfur exists in the air.
2. The capacitance values of high dielectric constant capacitors will gradually decrease with the passage of time, ｓ o care shall be taken to design circuits . Even if
capacitance value decreases as time passes, it will get back to the initial value by a heat treatment at 150 ℃ for 1hour.
If capacitors are stored in a high temperature and humidity environment, it might rapidly cause poor solderability due to terminal oxidation and quality loss of taping/
packaging materials. For this reason, capacitors shall be used within 6 months from the time of delivery. If exceeding the above period, please check solderability be-
fore using the capacitors.
※ RCR-2335B （ Safety Application Guide for ?xed ceramic capacitors for use in electronic equipment ） is published by JEITA.
Please check the guide regarding precautions for de?ection test, soldering by spot heat, and so on.
＊ This catalog contains the typical speci ?cation only due to the limitation of space. When you consider the purchase of our products, please check our speci ?cation.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) or CD catalogs.
mlcc_prec_e-01
12
mlcc_prec-P4
相关PDF资料 |
PDF描述 |
|---|---|
| E2K212BJ105KD-T | CAP ARRAY 2CH 1UF 16V 0805 |
| MB2411S2W13 | SWITCH PUSHBUTTON SPDT 3A 125V |
| BDH107 | HANDLE PISTOL 2.6" RED/YELLOW |
| MB2411A1W01-HC | SWITCH PUSHBUTTON SPDT 3A 125V |
| SFELF10M7HA00-A0 | FILTER 10.7MHZ 180KHZ BAND RADIA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L2K110BJ474KA-T | 功能描述:电容器阵列与网络 CAP ARRAY 0504 10V X5R .047uF 20% RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| L2K212BJ105KD-T | 功能描述:电容器阵列与网络 CAP ARRAY 0805 10V X5R 1uF 10% RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| L2K212BJ105MD-T | 功能描述:电容器阵列与网络 CAP ARRAY 0805 10V X5R 1uF 20% RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| L2K212BJ225MD-T | 功能描述:电容器阵列与网络 CAP ARRAY 0805 X5R 2.2uF 20% RoHS:否 制造商:AVX 电容:0.1 uF 容差:20 % 电压额定值:6.3 V 元件数量:2 工作温度范围: 外壳长度:0.8 mm 外壳宽度:1.6 mm 外壳高度:0.5 mm 端接类型:SMD/SMT 系列:PG |
| L-2K2-F1-352 | 制造商:Ohmite Mfg Co 功能描述: |
发布紧急采购，3分钟左右您将得到回复。