- 您现在的位置：买卖IC网 > PDF目录67754 > L5989DTR (STMICROELECTRONICS) 5.06 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | L5989DTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 5.06 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | ROHS COMPLIANT, HTSSOP-16 |
| 文件页数： | 9/51页 |
| 文件大小： | 1947K |
| 代理商： | L5989DTR |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
L5989D
Functional description
Doc ID 15778 Rev 3
17/51
5.3
External voltage reference
An external 1.8 V regulated voltage is provided. This reference is useful to set the voltage at
the multifunction pin (see Chapter 5.1) or to source current to ILIM-ADJ and FSW pins (see
and Chapter 5.5.2). The typical current capability is 4 mA.
5.4
Soft-start
When VCC is above the selected UVLO threshold the start-up phase takes place. At start-
up, a voltage ramp is generated charging the external capacitor CSS with an internal current
generator. The device is in inhibit mode as long as SS/INH pin is below the INH threshold.
The L5989D implements the soft-start phase by clamping the output of the error amplifier
and, being based on a voltage mode control, the duty cycle. In fact the comparison between
the output of the error amplifier and the internal saw tooth waveform generates the duty
cycle needed to keep the output voltage in regulation.
Two different current sources charge the external capacitor depending on the pin voltage in
order to reduce the power consumption in INH mode.
The equation for the soft-start time is:
Considering ISS2/ISS1 = 22/5 = 4.4, the proper soft-start capacitor is simply calculated as
follows:
During the soft-start phase (VSS < 2.9 V):
●
the sink capability is always disabled (independently from the multifunction pin settings)
to be compatible with pre-biased output voltage
●
in case the overcurrent limit is detected, a constant current protection is provided in
order to deliver extra current for charging the output capacitor (see Chapter 5.5.2 for
description of current protection management).
I
SS
I
SS1
5
=
μA
0
V
SS/INH
1
<<
I
SS2
2
=
2
μA
1
V
SS/INH
2.9
<<
=
T
SS
T
1
Δ
T
2
Δ
+
C
SS
I
SS1
-----------
10
–
()
×
C
SS
I
SS2
-----------
2.9
1
–
()
×
+
==
CnF
()
Tss mS
() 3.5
×
=
相关PDF资料 |
PDF描述 |
|---|---|
| L5989D | 5.06 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| L5991D013TR | 1.5 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| L6258EX | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO36 |
| L6470PD | STEPPER MOTOR CONTROLLER, 7 A, PDSO36 |
| L6566BTR | 0.8 A POWER FACTOR CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L5991 | 功能描述:电流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L5991_01 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:PRIMARY CONTROLLER WITH STANDBY |
| L5991A | 功能描述:电流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| L5991AD | 功能描述:开关变换器、稳压器与控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| L5991AD13TR | 功能描述:电流型 PWM 控制器 Prog Current Mode RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。