- 您现在的位置：买卖IC网 > PDF目录95588 > L6219DS STEPPER MOTOR CONTROLLER, 1 A, PDSO24 PDF资料下载
参数资料
| 型号： | L6219DS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| 封装： | SOIC-24 |
| 文件页数： | 6/8页 |
| 文件大小： | 961K |
| 代理商： | L6219DS |
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
L6219DS
DUAL FULL-BRIDGE
MOTOR DRIVER
Current Sensing
To minimize current sensing inaccuracies caused by ground
trace IR drops, each current-sensing resistor should have a
separate return to the ground terminal of the device. For low-
value sense resistors, the IR drops in the PCB can be significant
and should be taken into account. The use of sockets should be
avoided as their contact resistance can cause variations in the
effective value of RS.
Generally, larger values of RS reduce the aforementioned effects
but can result in excessive heating and power loss in the sense
resistor. The selected value of RS should not cause the absolute
maximum voltage rating of 1.5 V, for the SENSE terminal, to be
exceeded. The recommended value of RS is in the range of:
RS = 0.75 / ITRIP(max) ± 50% .
If desired, the reference input voltage can be filtered by placing
a capacitor from REFIN to ground. The ground return for this
capacitor as well as the bottom of any resistor divider used
should be independent of the high-current power-ground trace to
avoid changes in REFIN due to IR drops.
Thermal Considerations
For reliable operation, it is recommended that the maximum
junction temperature be kept below 110°C to 125°C. The
junction temperature can be measured best by attaching a
thermocouple to the power tab or batwing of the device and
measuring the tab temperature, TTAB . The junction temperature
can then be approximated by using the formula:
TJ = TTAB + (2 × ILOAD × VF × RθJT) ,
where V Fcan be chosen from the electrical specification table
for the given level of ILOAD. The value for RθJTis approximately
6°C/W.
The power dissipation of a batwing package can be improved
20% to 30% by adding a section of printed circuit board copper
(typically 6 to 18 square centimeters) connected to the batwing
terminals of the device.
The thermal performance in applications that run at high load
currents, high duty cycles, or both can be improved by adding
external diodes from each output to ground in parallel with the
internal diodes. Fast-recovery ( ≤200 ns) diodes should be used
to minimize switching losses.
Load Supply Terminal
The load supply terminal, VBB, should be decoupled with an
electrolytic capacitor ( ≥47F is recommended), placed as close
to the device as is physically practical. To minimize the effect of
system ground IR drops on the logic and reference input signals,
the system ground should have a low-resistance return to the
load supply voltage.
Fixed Off-Time Selection
With increasing values of tOFF, switching losses decrease, low-
level load current regulation improves, EMI reduces, PWM
frequency decreases, and ripple current increases. The value of
tOFFcan be chosen for optimization of these parameters. For
applications where audible noise is a concern, typical values of
tOFFshould be chosen in the range of 15 to 35 s.
APPLICATION NOTES
相关PDF资料 |
PDF描述 |
|---|---|
| L6219DSTR | STEPPER MOTOR CONTROLLER, 1 A, PDSO24 |
| L6234D | BRUSHLESS DC MOTOR CONTROLLER, 2.5 A, PDSO20 |
| L6243DS | VOICE COIL MOTOR CONTROLLER, 1.2 A, PDSO24 |
| L6287 | SPECIALTY ANALOG CIRCUIT, PDIP42 |
| L6670 | SPECIALTY ANALOG CIRCUIT, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6219DS013TR | 功能描述:马达/运动/点火控制器和驱动器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6219DS013TRE | 制造商:STMicroelectronics 功能描述: |
| L6219DSA | 功能描述:马达/运动/点火控制器和驱动器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6219DSA_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Stepper motor driver for automotive range |
| L6219DSA13TR | 功能描述:马达/运动/点火控制器和驱动器 Dual Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。