- 您现在的位置：买卖IC网 > PDF目录43899 > L6226PD (STMICROELECTRONICS) BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO36 PDF资料下载
参数资料
| 型号： | L6226PD |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 2.8 A, PDSO36 |
| 封装： | POWER, SO-36 |
| 文件页数： | 28/31页 |
| 文件大小： | 525K |
| 代理商： | L6226PD |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页
Pin connections
L6226
6/31
Doc ID 9452 Rev 4
9
24
OCDB
Open drain
output
Bridge B overcurrent detection and thermal
protection pin.An internal open drain
transistor pulls to GND when overcurrent
on bridge B is detected or in case of
thermal protection.
10
25
SENSEB
Power
supply
Bridge B source pin. This pin must be
connected to power ground directly or
through a sensing power resistor.
11
26
IN1B
Logic input
Bridge B input 1
12
27
IN2B
Logic input
Bridge B input 2
13
28
PROGCLB
R pin
Bridge B overcurrent level programming. A
resistor connected between this pin and
Ground sets the programmable current
limiting value for the bridge B. By
connecting this pin to Ground the
maximum current is set.This pin cannot be
left non-connected.
14
29
ENB
Logic input
Bridge B enable. LOW logic level switches
OFF all Power MOSFETs of bridge B. If not
used, it has to be connected to +5V.
15
30
VBOOT
Supply
voltage
Bootstrap voltage needed for driving the
upper Power MOSFETs of both bridge A
and bridge B.
16
32
OUT2B
Power
output
Bridge B output 2.
17
33
VSB
Power
supply
Bridge B power supply voltage. it must be
connected to the supply voltage together
with pin VSA.
20
4
VSA
Power
supply
Bridge A power supply voltage. it must be
connected to the supply voltage together
with pin VSB.
21
5
OUT2A
Power
output
Bridge A output 2.
22
7
VCP
Output
Charge pump oscillator output.
Table 4.
Pin description (continued)
Pin n.
Name
Type
Function
SO24/
PowerDIP24
PowerSO36
相关PDF资料 |
PDF描述 |
|---|---|
| L6226QTR | BRUSH DC MOTOR CONTROLLER, QCC32 |
| L6226Q | BRUSH DC MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6227N | STEPPER MOTOR CONTROLLER, 2.8 A, PDIP24 |
| L6228Q | STEPPER MOTOR CONTROLLER, 2.8 A, QCC32 |
| L6228QTR | STEPPER MOTOR CONTROLLER, QCC32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6226PDTR | 功能描述:马达/运动/点火控制器和驱动器 Dual Full Bridge RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6226Q | 功能描述:功率驱动器IC DMOS Full Bridge Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| L6226Q_10 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DMOS dual full bridge driver |
| L6226QTR | 功能描述:功率驱动器IC DMOS Full Bridge Driver RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| L6227 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DMOS DUAL FULL BRIDGE DRIVER WITH PWM CURRENT CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。