- 您现在的位置：买卖IC网 > PDF目录97995 > L6470HTR (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, 7 A, PDSO28 PDF资料下载
参数资料
| 型号： | L6470HTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 7 A, PDSO28 |
| 封装： | ROHS COMPLIANT, HTSSOP-28 |
| 文件页数： | 26/64页 |
| 文件大小： | 814K |
| 代理商： | L6470HTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
Phase current control
L6470
32/64
Doc ID 16737 Rev 2
7.4
BEMF compensation
Using the speed information, a compensation curve is added to the amplitude of the voltage
waveform applied to the motor winding in order to compensate the BEMF variations during
acceleration and deceleration (see Figure 14).
Compensation curve is approximated by a stacked line with a starting slope (ST_SLP) when
speed is lower than a programmable threshold speed (INT_SPEED) and a fine slope
(FN_SLP_ACC and FN_SLP_DEC) when speed is greater than the threshold speed (see
To obtain different current values during acceleration and deceleration phase two different
final slope values, and consequently two different compensation curves, can be
programmed.
Acceleration compensation curve is applied when the motor runs. No BEMF compensation
is applied when the motor is stopped.
7.5
Motor supply voltage compensation
The sinewave amplitude generated by the PWM modulators is directly proportional to the
motor supply voltage (VS). When the motor supply voltage is different from its nominal value,
the motor phases are driven with an incorrect voltage. The L6470 can compensate motor
supply voltage variations in order to avoid this effect.
The motor supply voltage should be connected to the integrated ADC input through a
resistor divider in order to obtain VREG/2 voltage at the ADCIN pin when VS is at its nominal
value (see Figure 15).
The ADC input is sampled at fS frequency, which is equal to PWM frequency.
Figure 14.
BEMF compensation curve
相关PDF资料 |
PDF描述 |
|---|---|
| L6562DTR | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6562D | 0.8 A POWER FACTOR CONTROLLER, PDSO8 |
| L6563HTR | POWER FACTOR CONTROLLER, PDSO16 |
| L6563H | POWER FACTOR CONTROLLER, PDSO16 |
| L6565N | 0.7 A SWITCHING CONTROLLER, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6470HTR-CUT TAPE | 制造商:ST 功能描述:L6470H Series 45 V Quad Output dSPIN Microstepping Motor Driver - HTSSOP-28 |
| L6470PD | 功能描述:马达/运动/点火控制器和驱动器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6470PDTR | 功能描述:马达/运动/点火控制器和驱动器 dSPIN 7.0A 8 - 45 V DMOS Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L64710GC-30 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Encoder/Decoder |
| L64710GC-40 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Encoder/Decoder |
发布紧急采购，3分钟左右您将得到回复。