- 您现在的位置：买卖IC网 > PDF目录53604 > L6506D (STMICROELECTRONICS) STEPPER MOTOR CONTROLLER, PDSO20 PDF资料下载
参数资料
| 型号： | L6506D |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, PDSO20 |
| 封装： | SO-20 |
| 文件页数： | 3/8页 |
| 文件大小： | 474K |
| 代理商： | L6506D |
ELECTRICAL CHARACTERISTICS (continued)
COMPARATOR SECTION PERFORMANCE (Over Operating Temperature Range)
Symbol
Parameter
Test Condtions
Min.
Typ.
Max.
Unit
VIO
Input Offset Voltage
VIN = 1.4V
±20
mV
IIO
Input Offset Curent
±500
nA
CIRCUIT OPERATION
The L6506 is intended for use with dual bridge driv-
ers, such as the L298, quad darlington arrays, such
as the L7150, quad DMOS array such as L6114-
L6115, or discrete power transistors to drive stepper
motors and other similar loads. The main function of
the device is to sense and control the current in each
of the load windings.
A common on-chip oscillator drives the dual chopper
and sets the operating frequency for the pulse width
modulated drive. The RC network on pin 1 sets the
operating frequency which is given by the equation
:
1
f =
for R
> 10 K
0.69 RC
The oscillator provides pulses to set the two flip-
flops which in turn cause the outputs to activate the
drive. When the current in the load winding reaches
the programmed peak value, the voltage across the
sense resistor (Rsense) is equal to Vref and the cor-
responding comparator resets its flip-flop interrupt-
ing the drive current until the next oscillator pulse oc-
curs. The peak current in each winding is pro-
grammed by selecting the value of the sense resis-
tor and Vref. Since separate inputs are provided for
each chopper, each of the loads may be pro-
grammed independently allowing the device to be
used to implement microstepping of the motor.
Lower threshold of L6506’s oscillator is 1/3 VCC. Up-
per threshold is 2/3 VCC and internal discharge re-
sistor is 1 K
± 30 %.
Ground noise problems in multiple configurations
can be avoided by synchronizing the oscillators.
This may be done by connecting the sync pins of
each of the devices with the oscillator output of the
master device and connecting the R/C pin of the un-
used oscillators to ground.
The equations for the active time of the sync pulse
(T2), the inactive time of the sync signal (T1) and the
duty cycle can be found by looking at the figure 1 and
are :
R1 RIN
T2 = 0.69 C1
(1)
R1 + RIN
T1 = 0.69 R1 C1
(2)
T2
DC =
(3)
T1 + T2
LOGIC SECTION (Over Operating Temperature Range - TTL compatible inputs & outputs)
Symbol
Parameter
Test Condtions
Min.
Typ.
Max.
Unit
VIH
Input High Voltage
2
Vs
V
VIL
Input Low Voltage
0.8
V
VOH
Output High Voltage
VCC = 4.75V
IOH = 400
A
2
3.5
V
VOL
Ouptut Low Voltage
VCC = 4.75V
IOH = 4mA
0.25
0.4
V
IOH
Ouput Source Current - Outputs
1 - 4
VCC = 4.75V
2.75
mA
OSCILLATOR
Symbol
Parameter
Test Condtions
Min.
Typ.
Max.
Unit
fosc
Frequency Range
5
70
KHz
VthL
Lower Threshold Voltage
0.33 VCC
V
VthH
Higher Threshold Voltage
0.66 VCC
V
Ri
Internal Discharge Resistor
0.7
1
1.3
k
L6506 - L6506D
3/8
相关PDF资料 |
PDF描述 |
|---|---|
| L6902D013TR | 3.2 A SWITCHING REGULATOR, 287 kHz SWITCHING FREQ-MAX, PDSO8 |
| L6911B | 3-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO20 |
| L9468N | SPECIALTY ANALOG CIRCUIT, SFM8 |
| L9830 | 2 A SWITCHING CONTROLLER, PSFM7 |
| L99PM60STR | POWER SUPPLY MANAGEMENT CKT, PDSO16 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6506D013TR | 功能描述:马达/运动/点火控制器和驱动器 Stepper Motor RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L6506D013TRE | 制造商:STMicroelectronics 功能描述: |
| L6506D1 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Stepper Motor Controller/Driver |
| L6506DC013TR | 制造商:STMicroelectronics 功能描述:A 制造商:STMicroelectronics 功能描述:INDUSTRIAL & ASIC - Tape and Reel 制造商:STMicroelectronics 功能描述:Current CTRL Stepper 10V VCC 25mA |
| L650BB | 制造商:Thomas & Betts 功能描述:BB TERMINAL LUG |
发布紧急采购，3分钟左右您将得到回复。