参数资料
型号: L6566A
厂商: STMICROELECTRONICS
元件分类: 稳压器
英文描述: 0.8 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 300 kHz SWITCHING FREQ-MAX, PDSO16
封装: LEAD FREE, SOP-16
文件页数: 26/51页
文件大小: 646K
代理商: L6566A
Application information
L6566A
32/51
Figure 19.
Possible interfaces between the L6566A and a PFC controller
To prevent intermittent operation of the PFC stage, some hysteresis is provided: if the
internal switch is open, it will be closed (which will re-enable the PFC pre-regulator) when
VCOMP exceeds VCOMPL > VCOMPO. Additionally, to reject VCOMP undershoots during
transients VCOMP must stay below VCOMPO for more than 1024 oscillator cycles in order for
the Vcc_PFC pin to open. Entering burst-mode (VCOMP < VCOMPBM) will open Vcc_PFC
immediately.
Besides pin 6 going open, when VCOMP falls below VCOMPO the UVLO threshold is set 2.4 V
below to compensate for the drop of the voltage delivered by the self-supply circuit that
occurs at light load (see Section 5.4: Adaptive UVLO on page 25).
5.9
Latched disable function
The device is equipped with a comparator having the non-inverting input externally available
at the pin DIS (8) and with the inverting input internally referenced to 4.5 V. As the voltage
on the pin exceeds the internal threshold, the device is immediately shut down and its
consumption reduced to a low value.
The information is latched and it is necessary to let the voltage on the Vcc pin go below the
UVLO threshold to reset the latch and restart the device. To keep the latch supplied as long
as the converter is connected to the input source, the HV generator is activated periodically
so that Vcc oscillates between the start-up threshold VccON and VccON - 0.5 V. Activating the
HV generator in this way cuts its power dissipation approximately by three (as compared to
the case of continuous conduction) and keeps peak silicon temperature close to the average
value.
To let the L6566A restart it is then necessary to disconnect the converter from the input
source. Pulling pin 16 (AC_OK) below the disable threshold (see Section 5.12: Brownout
) will stop the HV generator until Vcc falls below Vccrestart, so that the
latch can be cleared and a quicker restart is allowed as the input source is removed. This
operation is shown in the timing diagram of Figure 20.
This function is useful to implement a latched overtemperature protection very easily by
biasing the pin with a divider from VREF, where the upper resistor is an NTC physically
located close to a heating element like the MOSFET, or the transformer. The DIS pin is a
high impedance input, thus it is prone to pick up noise, which might give origin to undesired
latch-off of the device. It is possible to bypass the pin to ground with a small film capacitor
(e.g. 1-10 nF) to prevent any malfunctioning of this kind.
L6566A
Vcc_PFC
6
5
Vcc
L6566A
Vcc_PFC
6
L6563
5
Vcc
RUN
4.7k
Ω
22 k
Ω
10
L6561
L6562
L6563
相关PDF资料
PDF描述
L6712AQTR 2 A SWITCHING CONTROLLER, QCC36
LNK604GG-TL SPECIALTY ANALOG CIRCUIT, PDSO8
LM385DR-2-5 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8
LM4041DIM-ADJ 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.233 V, PDSO8
LS4601-9RD1TB1 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE
相关代理商/技术参数
参数描述
L6566A_08 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Multi-mode controller for SMPS with PFC front-end
L6566ATR 功能描述:开关变换器、稳压器与控制器 Multi Mode PWM Controller RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
L6566B 功能描述:开关变换器、稳压器与控制器 Multi Mode PWM Controller RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel
L6566B_08 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Multi-mode controller for SMPS
L6566BH 功能描述:电流型 PWM 控制器 Multimode Controller SMPS 800V <3mA RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14