- 您现在的位置：买卖IC网 > PDF目录79745 > L6566A (STMICROELECTRONICS) 0.8 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 300 kHz SWITCHING FREQ-MAX, PDSO16 PDF资料下载
参数资料
| 型号： | L6566A |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 0.8 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 300 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封装： | LEAD FREE, SOP-16 |
| 文件页数： | 35/51页 |
| 文件大小： | 646K |
| 代理商： | L6566A |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页当前第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页
Application information
L6566A
40/51
the base terminal are several ten kW) but this could distort the signal on the MULT pin of the
PFC chip and adversely affect the operation of the pre-regulator. CF needs to be quite a big
capacitor (in the
μF) to have small residual ripple superimposed on the dc level; as a rule-of-
thumb, use a time constant (RL + RH)CF at least 4-5 times the maximum line cycle period,
then fine tune if needed, considering also transient conditions such as mains missing
cycles.
If temperature effects are critical, the NPN Q can be replaced by a PNP-NPN pair arranged
as shown in Figure 26 on page 39 on the right-hand side; other sensing techniques can be
adopted anyway.
The voltage on the pin is clamped upwards at about 3.15 V; then, if the function is not used
the pin has to be connected to Vcc through a resistor (220 to 680 k
Ω).
5.13
Slope compensation
The pin MODE/SC (12), when not connected to VREF, provides a voltage ramp during
MOSFET's ON-time synchronous to that of the internal oscillator sawtooth, with 0.8 mA
minimum current capability. This ramp is intended for implementing additive slope
compensation on current sense. This is needed to avoid the sub-harmonic oscillation that
arises in all peak-current-mode-controlled converters working at fixed frequency in
continuous conduction mode with a duty cycle close to or exceeding 50 %.
Figure 27.
Slope compensation waveforms
The compensation will be realized by connecting a programming resistor between this pin
and the current sense input (pin 7, CS). The CS pin has to be connected to the sense
resistor with another resistor to make a summing node on the pin. Since no ramp is
delivered during MOSFET OFF-time (see Figure 27), no external component other than the
programming resistor is needed to ensure a clean operation at light loads.
Note:
The addition of the slope compensation ramp will reduce the available dynamics of the
current signal; thereby, the value of the sense resistor must be determined taking this into
account. Note also that the burst-mode threshold (in terms of power) will be slightly
changed.
If slope compensation is not required with FF operation, the pin shall be left floating.
Internal
oscillator
GD
(pin 4)
MODE/SC
(pin 12)
t
相关PDF资料 |
PDF描述 |
|---|---|
| L6712AQTR | 2 A SWITCHING CONTROLLER, QCC36 |
| LNK604GG-TL | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LM385DR-2-5 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 2.5 V, PDSO8 |
| LM4041DIM-ADJ | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.233 V, PDSO8 |
| LS4601-9RD1TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6566A_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Multi-mode controller for SMPS with PFC front-end |
| L6566ATR | 功能描述:开关变换器、稳压器与控制器 Multi Mode PWM Controller RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| L6566B | 功能描述:开关变换器、稳压器与控制器 Multi Mode PWM Controller RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| L6566B_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:Multi-mode controller for SMPS |
| L6566BH | 功能描述:电流型 PWM 控制器 Multimode Controller SMPS 800V <3mA RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。