- 您现在的位置：买卖IC网 > PDF目录97995 > L6911ETR (STMICROELECTRONICS) 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 PDF资料下载
参数资料
| 型号： | L6911ETR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | 1.3 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封装： | SO-20 |
| 文件页数： | 7/34页 |
| 文件大小： | 558K |
| 代理商： | L6911ETR |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页
Obsolete
Product(s)
- Obsolete
Product(s)
Obsolete
Product(s)
- Obsolete
Product(s)
L6911E
Device description
15/34
5.5
Monitor and protection
The output voltage is monitored by means of pin 1 (VSEN). If it is not within ±10% (typ.) of
the programmed value, the powergood output is forced low.
The device provides overvoltage protection, when the output voltage reaches a value 17%
(typ.) greater than the nominal one. If the output voltage exceed this threshold, the OVP pin
is forced high (5V) and the lower driver is turned on as long as the over-voltage is detected.
The OVP pin is capable to deliver up to 60mA (min) in order to trigger an external SCR
connected to burn the input fuse. The low-side mosfet turn-on implement this function when
the SCR is not used and helps in keeping the ouput low.
To perform the overcurrent protection the device compares the drop across the high side
MOS, due to its
RDSON, with the voltage across the external resistor (ROCS) connected between the
OCSET pin and drain of the upper MOS. Thus the overcurrent threshold (IP) can be
calculated with the following relationship:
Equation 4
where the typical value of IOCS is 200A.
To calculate the ROCS value it must be considered the maximum RDSON (also the variation
with temperature) and the minimum value of IOCS. To avoid undesirable trigger of
overcurrent protection this relationship must be satisfied:
Equation 5
where
I is the inductance ripple current and I
OUTMAX is the maximum output current.
In case of output short circuit the soft start capacitor is discharged with constant current
(10
A typ.) and when the SS pin reaches 0.5V the soft start phase is restarted. During the
soft start the over-current protection is always active and if such kind of event occours, the
device turns off both mosfets, and the SS capacitor is dicharged again after reaching the
upper threshold of about 4V. The system is now working in HICCUP mode, as shown in
Figure 7 on page 16 a. After removing the cause of the over-current, the device restart
working normally without power supplies turn off and on.
I
P
I
OCS
R
OCS
R
DSON
--------------------------------
=
I
P
I
OUTMAX
l
2
-----
+
≥
I
PEAK
=
相关PDF资料 |
PDF描述 |
|---|---|
| L6924U013 | POWER SUPPLY SUPPORT CKT, PQCC16 |
| L6924U013TR | POWER SUPPLY SUPPORT CKT, PQCC16 |
| L6924U | POWER SUPPLY SUPPORT CKT, QCC16 |
| L6926D1013TR | 1.65 A SWITCHING REGULATOR, 800 kHz SWITCHING FREQ-MAX, PDSO8 |
| L6996D | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6912-2 | 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,2/BG |
| L6913-1 | 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,1/BG |
| L6913-2 | 制造商:Thomas & Betts 功能描述:1/2 CORD GRIP CONNECTOR,2/BG |
| L6916D | 功能描述:运算放大器 - 运放 POWER SUPPLY RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
| L6916DTR | 功能描述:运算放大器 - 运放 POWER SUPPLY RoHS:否 制造商:STMicroelectronics 通道数量:4 共模抑制比（最小值）:63 dB 输入补偿电压:1 mV 输入偏流（最大值）:10 pA 工作电源电压:2.7 V to 5.5 V 安装风格:SMD/SMT 封装 / 箱体:QFN-16 转换速度:0.89 V/us 关闭:No 输出电流:55 mA 最大工作温度:+ 125 C 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。