- 您现在的位置：买卖IC网 > PDF目录240255 > L6918DTR (STMICROELECTRONICS) SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PDSO28 PDF资料下载
参数资料
| 型号： | L6918DTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | SO-28 |
| 文件页数： | 30/35页 |
| 文件大小： | 431K |
| 代理商： | L6918DTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页
L6918 L6918A
4/35
13
ISEN1
Channel 1 current sense pin. The output current may be sensed across a sense resistor or
across the low-side mosfet RdsON. This pin has to be connected to the low-side mosfet drain
or to the sense resistor through a resistor Rg in order to program the current intervention for
each phase at 140% as follow:
Where 35
A is the current offset information relative to the Over Current condition (offset at
OC threshold minus offset at zero load).The net connecting the pin to the sense point must be
routed as close as possible to the PGNDS1 net in order to couple in common mode any
picked-up noise.
14
PGNDS1
Channel 1 Power Ground sense pin. The net connecting the pin to the sense point must be routed as
close as possible to the ISEN1 net in order to couple in common mode any picked-up noise.
15
PGNDS2
Channel 2 Power Ground sense pin. The net connecting the pin to the sense point must be
routed as close as possible to the ISEN2 net in order to couple in common mode any picked-
up noise.
16
ISEN2
Channel 2 current sense pin. The output current may be sensed across a sense resistor or
across the low-side mosfet RdsON. This pin has to be connected to the low-side mosfet drain
or to the sense resistor through a resistor Rg in order to program the current intervention for
each phase at 140% as follow:
Where 35
A is the current offset information relative to the Over Current condition (offset at
OC threshold minus offset at zero load).
The net connecting the pin to the sense point must be routed as close as possible to the
PGNDS2 net in order to couple in common mode any picked-up noise.
17
OSC/INH
FAULT
Oscillator switching frequency pin. Connecting an external resistor from this pin to GND, the
external frequency is increased according to the equation:
Connecting a resistor from this pin to Vcc (12V), the switching frequency is reduced according
to the equation:
If the pin is not connected, the switching frequency is 300KHz.
Forcing the pin to a voltage lower than 0.8V, the device stop operation and enter the inhibit
state; all mosfets are turned OFF.
18
to
22
VID0-4
Voltage Identification pins. These input are internally pulled-up and TTL compatible. They are
used to program the output voltage as specified in Table 1 and to set the over voltage and
power good thresholds.
Connect to GND to program a ‘0’ while leave floating to program a ‘1’.
23
PGOOD
This pin is an open collector output and is pulled low if the output voltage is not within the
above specified thresholds. It must be connected with the Slave’s PGOOD pin.
If not used may be left floating.
24
BOOT2
Channel 2 bootstrap capacitor pin. This pin supplies the high side driver. Connect through a
capacitor to the PHASE2 pin and through a diode to Vcc (cathode vs. boot).
25
UGATE2
Channel 2 high side gate driver output.
26
PHASE2
This pin is connected to the source of the upper mosfet and provides the return path for the
high side driver of channel 2.
27
LGATE2
Channel 2 low side gate driver output.
28
PGND
Power ground pin. This pin is common to both sections and it must be connected through the closest
path to the low side mosfets source pins in order to reduce the noise injection into the device.
L6918A (MASTER) PIN FUNCTION (continued)
N.
Name
Description
I
OCPx
35
AR
g
R
sense
--------------------------
=
I
OCPx
35
AR
g
R
sense
--------------------------
=
f
S
300KHz
14.82 10
6
R
OSC K
()
-----------------------------
+
=
f
S
300KHz
12.91 10
7
R
OSC K
()
-----------------------------
+
=
相关PDF资料 |
PDF描述 |
|---|---|
| LES008YDN1 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YHN2 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015YJN19 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015ZHN38 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
| LES015ZJN19 | 1-OUTPUT 15 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L6919 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:5 BIT PROGRAMMABLE DUAL-PHASE CONTROLLER WITH DYNAMIC VID MANAGEMENT |
| L6919C | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:5 BIT PROGRAMMABLE DUAL-PHASE CONTROLLER WITH DYNAMIC VID MANAGEMENT |
| L6919CD | 功能描述:DC/DC 开关控制器 Prog Dual-Phase Cont RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| L6919CDTR | 功能描述:DC/DC 开关控制器 Prog Dual-Phase Cont RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| L6919E | 功能描述:DC/DC 开关控制器 5-Bit Dual Ph Contlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。