- 您现在的位置：买卖IC网 > PDF目录43901 > L7250 (STMICROELECTRONICS) VOICE COIL MOTOR CONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | L7250 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 运动控制电子 |
| 英文描述： | VOICE COIL MOTOR CONTROLLER, PQFP64 |
| 封装： | TQFP-64 |
| 文件页数： | 17/46页 |
| 文件大小： | 478K |
| 代理商： | L7250 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页
L7250
24/46
2.7.2 Open Loop Commutation
After position sense is complete, the microcontroller commutates the motor following a constant acceleration
profile until sufficient BEMF is developed to reliably measure it.
The starting position of the open loop commutation, determined by the position sense routine, is set up by first
initializing the Memory Address Counter using LOADCP (*1), then clocking ADVANCE (*2) the appropriate
number of times (8 pulses per 6 state position). The spindle state will be OLCOAST while setting the initial state.
Then, drivers are enabled in either OL_SIX or OL_SIN modes (*3) , depending on whether 6 state or sine mode
open loop commutation is desired. Once the motor is accelerated up to an appropriate speed (*4) , the motor
is tri-stated by transitioning to the OLCOAST (*5) and then CLCOAST states, as described below, to synchro-
nize the Smoothdrive system to the motor.
Figure 5. Open Loop Commutation
2.7.3 Synchronization to Smoothdrive Commutation
When the open loop commutation is complete, the drivers are put in OLCOAST mode, and after a delay for set-
ting the Bemf sampling period, CLCOAST is asserted, so that a ZC Period (Tc, the time between two BEMF
zero crossings) can be detected and measured.
The BEMF sampling period is set in OLCOAST (*1) and after a delay (30 usec ) a Load CP (*2) is asserted.
After a delay of time Tc0 (300usec suggested) another Load CP is asserted (*3); this initializes the electrical
period for BEMF sampling. Once pregrammed the transition to CLCOAST (*4) , the BEMF is sampled at the
rate of Tc0 to look for two consecutive LOW readings (in anticipation of the LOW->HI zero crossing transition
(*5) ).
After the first ZC rising edge, the BEMF sampling period is refreshed to Tc0 value.
If two consecutive ZC edges are detected (*6), then after the last rising edge the Smoothdrive commutation is
synchronized with the motor rotor position and it is ready to be programmed in closed loop commutation .
At least two ZCs must be observed before transitioning to closed loop spinup (CLSIX or CLSIN) (*7a or *7b) .
This ensures that the Smoothdrive circuitry is synchronized to the spindle motor.
Set Load Coarse Phase
Write Reg.07H
LoadCP = 1
(*1)
Set ADVANCE
Write Reg.07H
Advance = 1
Nadv=Nalign
Inc Nadv
START
Open Loop Commutation
Nadv=0 , i=0
Note2: Nalign is received from
the Inductive Sense routine
Indicating the rotor position
alignement
Accelerate in
Sine or Six
Set Open Loop SINE
Write Reg.03H
Spstate[3:0] =0011
Set Open Loop SIX
Write Reg.03H
Spstate[3:0] =0010
Set ADVANCE
Write Reg.07H
Advance = 1
Wait the End of
RAMP_DELAY[ i ]
Inc i
i = RAMP_Steps
Set OLCOAST
Write Reg.03H
Spstate[3:0]=0001
EXIT
Open Loop
Commutation
(*2)
(*3)
(*4)
(*5)
SINE
SIX
Note1: Spstate[3:0] condition has
been set in OLCOAST
by the Inductive Sense
Routine
相关PDF资料 |
PDF描述 |
|---|---|
| L7980A | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980 | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7980TR | 3.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO8 |
| L7981ATR | SWITCHING REGULATOR, DSO8 |
| L7981TR | SWITCHING REGULATOR, DSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L7250E1.2 | 功能描述:电源开关 IC - 配电 DSD POWER RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| L7252E2.6 | 功能描述:电源开关 IC - 配电 DSD POWER RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| L725MAG | 制造商:Apex Tool Group 功能描述:TAPE, 1 IN. X 25 FT, 700 SERIES, MAGNETIC END HOOK 制造商:Lufkin 功能描述:TAPE MEASURE, MAGNETIC END HOOK 25FT 1IN; Tape Measure Type:Manual; Measuring Range Max:25ft; Blade Width:1"; Case Color:Orange; Tool Body Material:ABS; Blade Finish:Yellow Clad; Blade Length:25ft ;RoHS Compliant: NA |
| L728 | 制造商:BURNDY 功能描述:L-DIE |
| L7290 | 制造商:CIPS 功能描述:CUTTER OBLIQUE SEMI FLUSH 109MM |
发布紧急采购，3分钟左右您将得到回复。