- 您现在的位置：买卖IC网 > PDF目录43901 > L7981ATR (STMICROELECTRONICS) SWITCHING REGULATOR, DSO8 PDF资料下载
参数资料
| 型号： | L7981ATR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, DSO8 |
| 封装： | 3 X 3 MM, 1.08 MM HEIGHT, ROHS COMPLIANT, HSOP-8 |
| 文件页数： | 44/44页 |
| 文件大小： | 1315K |
| 代理商： | L7981ATR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页
L7981
Functional description
Doc ID 15182 Rev 3
9/44
5.1
Oscillator and synchronization
Figure 4 shows the block diagram of the oscillator circuit. The internal oscillator provides a
constant frequency clock. Its frequency depends on the resistor externally connect to FSW
pin. In case the FSW pin is left floating the frequency is 250 kHz; it can be increased as
shown in Figure 6 by external resistor connected to ground.
To improve the line transient performance, keeping the PWM gain constant versus the input
voltage, the voltage feed forward is implemented by changing the slope of the sawtooth
according to the input voltage change (see Figure 5.a).
The slope of the sawtooth also changes if the oscillator frequency is increased by the
external resistor. In this way a frequency feed forward is implemented (Figure 5.b) in order to
keep the PWM gain constant versus the switching frequency (see Section 6.4 for PWM gain
expression).
On the SYNCH pin the synchronization signal is generated. This signal has a phase shift of
180° with respect to the clock. This delay is useful when two devices are synchronized
connecting the SYNCH pin together. When SYNCH pins are connected, the device with
higher oscillator frequency works as Master, so the Slave device switches at the frequency
of the Master but with a delay of half a period. This minimizes the RMS current flowing
through the input capacitor [see L5988D Data sheet].
Figure 4.
Oscillator circuit block diagram
The device can be synchronized to work at higher frequency feeding an external clock
signal. The synchronization changes the sawtooth amplitude, changing the PWM gain
(Figure 5.c). This changing has to be taken into account when the loop stability is studied.
To minimize the change of the PWM gain, the free running frequency should be set (with a
resistor on FSW pin) only slightly lower than the external clock frequency. This pre-adjusting
of the frequency will change the sawtooth slope in order to get negligible the truncation of
sawtooth, due to the external synchronization.
Clock
Generator
Ramp
Generator
FSW
Sawtooth
Clock
Synchronization
SYNCH
Clock
Generator
Ramp
Generator
FSW
Sawtooth
Clock
Synchronization
SYNCH
相关PDF资料 |
PDF描述 |
|---|---|
| L7981TR | SWITCHING REGULATOR, DSO8 |
| L8219LP | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO28 |
| L8219P | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO36 |
| L8229 | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO24 |
| L9484 | SWITCHING REGULATOR, 460 kHz SWITCHING FREQ-MAX, PSFM8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L7981ATR/BLK | 制造商:STMicroelectronics 功能描述:3 A STEP-DOWN SWITCHING REGULATO - Tape and Reel 制造商:STMicroelectronics 功能描述:STMicroelectronics L7981ATR/BLK Interface Misc |
| L7981TR | 功能描述:直流/直流开关调节器 3A DC 4.5 V to 28 V Adj 0.6V 250 kHz RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
| L7983 | 制造商:Leviton Manufacturing Co 功能描述: |
| L7985 | 功能描述:线性稳压器 - 标准 2A Step Down REG 4.5V to 38V 250 KHz RoHS:否 制造商:STMicroelectronics 输出类型: 极性: 输出电压:1.8 V 输出电流:150 mA 负载调节: 最大输入电压:5.5 V 线路调整率: 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:SOT-323-5L |
| L7985A | 功能描述:直流/直流开关调节器 2A DC 4.5V to 38V 250 KHz Step-Down RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5 |
发布紧急采购，3分钟左右您将得到回复。