收藏本站
参数资料
型号： L9911P
厂商： STMICROELECTRONICS
元件分类： 运动控制电子
英文描述： BRUSH DC MOTOR CONTROLLER, SFM8
封装： ROHS COMPLIANT, MULTIWATT-8
文件页数： 19/19页
文件大小： 276K
代理商： L9911P
L9911
Electrical specification
Doc ID 10990 Rev 6
9/19
DUTY-PR
Phase regulation max field ON
duty
see Figure 6
26.56
31.25
35.94
%
VH_SAT
High side driver saturation
Voltage (see Figure 8)
With driver Isource = 500 mA
-
1.5
V
VL_SAT
Low side driver saturation voltage
(see Figure 8)
With driver Isink = 500 mA
-
1.5
V
VLSB
Selfbias without supply lamp
driver voltage
B+ open; L connected to 12 V
through a 50 Ohm resistor
--
4
V
IHSC
High side driver short circuit
current protection
B+ = 12.5 V; L = GND
1.2
-
3
A
ILSC
Low Side Driver short circuit
current (see Figure 14)
B+ = L = 12.5 V
1
-
2
A
VthL
Enable regulator supply voltage
threshold
-0.8
-
1.15
V
Ipd_L
L terminal pull-down current when
the generator is not rotating
VL = 0.6 V
0.4
3.5
mA
IL_sink
L sink current when the generator
is rotating
P frequency 500 Hz; VB+ = 12 V
-
100
A
t-D
Diagnostic alarm delay time
-
0.2
-
0.5
s
Vcan-DFM
Test mode to cancel soft start/
attack (voltage)
(see Figure 9)
30
-
50
V
tcan-DFM
Test mode delay time
25
-
ms
VPHL1
Enable control voltage input high
threshold
square wave f = 1 kHz
-
0.35
V
VPHL2
Enable control voltage input low
threshold
square wave f = 1 kHz
-
0.25
V
tPHL1
Enable Control Voltage Phase
Filtering Time
-50
-
115
μs
VPHH1
Diagnosis phase loss input high
threshold
-8
9
10
V
VPHH2_1
Diagnosis phase loss input low
threshold
-6.4
7.4
8.4
V
tPHd
Diagnostic phase filtering time
-
50
-
100
s
IPd-P1
Phase pull-down current
VP = 0.8 V
1
-
8
mA
f-dfm
DFM output open drain switching
freq.
Ialt =1 A~0.9 Inom;
1400 rpm < rpm < RPMMAX;
Isink = 4 mA
125
-
200
Hz
VL-DFM
Output low voltage saturation
I-sink = 14 mA
-
1.5
V
I-SC_DFM
Short circuit current protection
VB+ = VDFM = 12.5 V
50
-
400
mA
Ilk-DFM
Output leakage current
VDFM =16 V at DFM driver OFF
-
5
A
Table 5.
Electrical characteristics (continued)
Symbol
Parameter
Test condition
Min.
Typ.
Max.
Unit
相关PDF资料
PDF描述
L9942XP1TR STEPPER MOTOR CONTROLLER, 2.5 A, PDSO24
L9949TR BRUSH DC MOTOR CONTROLLER, 10 A, PDSO20
L9950XPTR BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
L9950 BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
L9950TR BRUSH DC MOTOR CONTROLLER, 10 A, PDSO36
相关代理商/技术参数
参数描述
L9911U 制造商:STMicroelectronics 功能描述:PTS SMARTPOWER - Rail/Tube 制造商:STMicroelectronics 功能描述:IC VREG MULTIFUN AUTO MULTIWATT8 制造商:STMicroelectronics 功能描述:PTS Smartpower
L9911V 功能描述:低压差稳压器 - LDO Car Alternator Reg Multifunction Volt RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
L9914A 功能描述:低压差稳压器 - LDO Car Alternator Reg Multifunction Volt RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
L9914B 功能描述:低压差稳压器 - LDO Car Alternator Reg Multifunction Volt RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
L9914C 功能描述:低压差稳压器 - LDO Multi Gen Volt REG 40V 6W 8 to 16V RoHS:否 制造商:Texas Instruments 最大输入电压:36 V 输出电压:1.4 V to 20.5 V 回动电压（最大值）:307 mV 输出电流:1 A 负载调节:0.3 % 输出端数量: 输出类型:Fixed 最大工作温度:+ 125 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-20
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*