- 您现在的位置：买卖IC网 > PDF目录43901 > L9952GXPTR (STMICROELECTRONICS) 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 PDF资料下载
参数资料
| 型号： | L9952GXPTR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| 封装： | LEAD FREE, SSO-36 |
| 文件页数： | 15/68页 |
| 文件大小： | 859K |
| 代理商： | L9952GXPTR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
Description
L9952GXP
Doc ID 13518 Rev 5
2.17
Error handling
The L9952GXP provides the following 3 error handling features which are not described in
the LIN Spec. V2.1, but are realized in different stand alone LIN transceivers / micro
controllers to switch the application back to normal operation mode.
2.17.1
Dominant TxD time out
If TXI is in dominant state (low) for more than 12ms (typ) the transmitter will be disabled until
TXI becomes recessive (high). This feature can be disabled via SPI.
2.17.2
Short to battery time out
If TXI changes to dominant (low) state but RXI signal does not follow within 40
s, the
transmitter will be disabled until TXI becomes recessive (high).
2.17.3
Short to ground mode
A wake up caused by a message on the bus will start the voltage regulator and the micro
controller to switch the application back to normal operation mode.
2.18
Wake up (from LIN)
In standby mode the L9952GXP can receive a wake up from LIN bus. For the wake up
feature the L9952GXP logic differentiates two different conditions.
2.18.1
Normal wake up
Normal wake up can occur when the LIN transceiver was set in standby mode while LIN was
in recessive (high) state. A dominant level at LIN for at least 40s, will switch the L9952GXP
to active mode.
2.18.2
Wake up from short to GND condition
If the LIN transceiver was set in standby mode while LIN was in dominant (low) state,
recessive level at LIN for at least 40us, will switch the L9952GXP to active mode.
2.18.3
RxD pin in V1 standby
In V1 standby condition the RxD is a tristate pin.
相关PDF资料 |
PDF描述 |
|---|---|
| L99H01QF | BRUSH DC MOTOR CONTROLLER, PQFP32 |
| L99H01XPTR | BRUSH DC MOTOR CONTROLLER, PDSO36 |
| L99PM62XP | 4-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO36 |
| LA5635H | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LA5693D | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| L9952XP | 功能描述:马达/运动/点火控制器和驱动器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9952XPTR | 功能描述:马达/运动/点火控制器和驱动器 DOOR ACTUATOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L9953 | 功能描述:马达/运动/点火控制器和驱动器 Door actuator DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| L-995-38 | 制造商:MOLEX 制造商全称:Molex Electronics Ltd. 功能描述:NylaKrimp? Funnel Entry Ring Tongue Terminal for 4/0 AWG Wire, Stud #9 |
| L9953LXP | 功能描述:马达/运动/点火控制器和驱动器 DOOR ACTUATOR DRVR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。