- 您现在的位置：买卖IC网 > PDF目录95590 > LB11961V (SANYO SEMICONDUCTOR CO LTD) BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO16 PDF资料下载
参数资料
| 型号： | LB11961V |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO16 |
| 封装： | 0.225 INCH, SSOP-16 |
| 文件页数： | 5/7页 |
| 文件大小： | 72K |
| 代理商： | LB11961V |
LB11961V
No.8794-5/7
Application Circuit Example
*1.Power supply and ground lines
P-GND is connected to the motor power supply system and S-GND is connected to the control circuit power supply system.
These two systems should be formed from separate lines and the control system external components should be connected to
S-GND.
*2. Regeneration power supply stabilization capacitor
The capacitor CM provides power supply stabilization for both PWM drive and kickback absorption. A capacitor with a value of
over 0.1F is used for CM. A large capacitor must be used when the coil inductance is large or when the coil resistance is low.
Since this IC adopts a technique in which switching is performed by the high side transistor and regeneration is handled by the low
side transistor, the pattern connecting CM to VM and P-GND must be as wide and as short as possible.
*3.Hall sensor input
Lines that are as short as possible must be used to prevent noise from entering the system. The Hall sensor input circuit consists of
a comparator with hysteresis (20mV). We recommend that the Hall sensor input level be at least three times this hysteresis, i.e. at
least 60mVp-p.
*4.PWM oscillator frequency setting capacitor
If a value of 100pF is used for CP, the oscillator frequency will be f = 25kHz, and this will be the basic frequency of the PWM
signal.
*5.RD output
This is an open collector output. It outputs a low level when the motor is turning and a high level when it is stopped. This pin must
be left open if unused.
*6.FG output
This is an open collector output, and a rotation count detection function can be implemented using this FG output, which
corresponds to the phase switching. This pin must be left open if unused.
*7.HB pin
This pin provides a Hall effect sensor bias constant-voltage output of 1.25V.
*8.RMI pin
Connect this pin to VTH if unused. Even if unused, the IC is set internally to operate at a 10% drive duty at the voltage
corresponding to the lowest speed. (The capacitor is used to set up full-speed mode at startup.)
P-GND
VCC
FG
OUT1
OUT2
CT
VTH
IN
+
IN
CPWM
*3
CM
*1
*6
H
*2
*5
RMI
RD
HB
*8
S-GND
*4
*7
6VREG
CT = 0.47
μF to 1μF
CP = 100pF
相关PDF资料 |
PDF描述 |
|---|---|
| LB11961V | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO16 |
| LB11963T | BRUSHLESS DC MOTOR CONTROLLER, 0.5 A, PDSO8 |
| LB11965M | BRUSHLESS DC MOTOR CONTROLLER, PDSO14 |
| LB11985H | BRUSHLESS DC MOTOR CONTROLLER, 1.5 A, PDSO28 |
| LB11988H | BRUSHLESS DC MOTOR CONTROLLER, 1.3 A, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LB11961V-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11961V-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11961V-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11961V-TLM-H | 功能描述:马达/运动/点火控制器和驱动器 PWM MOTOR PREDRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LB11961-W-AH | 制造商:ON Semiconductor 功能描述:SINGLE PHASE MOTOR DRIVER - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / SINGLE PHASE MOTOR DRIVER 制造商:ON Semiconductor 功能描述:ON.HSSOP14.REEL.SPQ2000.MOQ2000/MPQ2000.LINEAR IC |
发布紧急采购，3分钟左右您将得到回复。