- 您现在的位置：买卖IC网 > PDF目录30738 > LC898023KW SPECIALTY CONSUMER CIRCUIT, PQFP208 PDF资料下载
参数资料
| 型号： | LC898023KW |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| 封装： | 28 X 28 MM, SQFP-208 |
| 文件页数： | 2/13页 |
| 文件大小： | 78K |
| 代理商： | LC898023KW |
No. 6614-10/13
LC898023KW, 898023KL
Pin Functions
<SCSI Interface Pins>
BSY, ACK, MSG, SEL, REQ, ATN, RST, I/O, C/D (input/output)
SCIS bus control.
DB0 to DB7, DBP (input/output)
SCSI data bus.
<Microcontroller Interface Pins>
CS (input)
Chip select signal from the microcontroller. The microcontroller interface is active when this pin is low.
RD, WR (input)
Connect the microcontroller read and write lines to these inputs.
SWAIT (input)
Wait signal output to the microcontroller. When accessing buffer RAM, the microcontroller must wait if this pin is
low.
SUA0 to SUA7 (input)
Internal register address lines
D0 to D7 (input)
Microcontroller data bus. These pins have built-in pull-up resistors.
INT0, INT1 (output)
Interrupt request signals output to the microcontroller. INT1 can be set to output the ATAPI interrupt by setting
INT1EN (Conf-R11 bit 7)
These are open drain outputs with built-in 80 k
(at room temperature, 5 V) pull-up resistors.
<Buffer RAM Pins>
I/O0 to I/O15 (input/output)
Buffer RAM data bus. These pins have built-in pull-up resistors.
RA0 to RA9 (output)
Buffer RAM address lines.
RAS0, RAS1, RAS2 (output)
Buffer DRAM RAS outputs. Normally, RAS0 is used. However, if two 16-Mbit DRAMs are used, connect the RAS0
and RAS1 lines to the RAS pins on the DRAMs. If four 16-Mbit DRAMs are used, connect the RAS0, RAS1, RAS2,
and LWE lines to the RAS pins on the DRAMs.
CAS0, CAS1 (output)
Buffer DRAM CAS outputs. Normally, CAS0 is used. However, if two 16-Mbit DRAMs are used, connect the CAS0
output to the CAS pins on the DRAMs. If 2-CAS type DRAMs are used, connect CAS0 to UCAS and CAS1 to
LCAS.
OE (output)
Buffer RAM read output.
UWE, LWE (output)
Buffer RAM write outputs. Connect these to the corresponding pins. If 2-CAS type DRAMs are used, UWE must be
connected. (Leave LWE open.)
1. Analog Interface Pins
CCS (input)
Midpoint servo input pin.
RREC (input)
Optical discrimination input.
FE (input)
Focus error signal input.
TE (input)
Tracking error signal input.
VREF (input)
Input for the servo system reference voltage.
相关PDF资料 |
PDF描述 |
|---|---|
| LC898023K | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| LC898023 | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| LC898093KW | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| LC898093KL | SPECIALTY CONSUMER CIRCUIT, PQFP208 |
| LC89915 | SPECIALTY CONSUMER CIRCUIT, PDIP8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LC898093 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:40ⅴ Playback/12ⅴ Write CD-R/RW Encoder/Decoder IC with Built-in ATAPI Interface |
| LC898093KL | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LC898093KW | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LC898094 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:LC898094 |
| LC898105-TBM-GB-E | 功能描述:马达/运动/点火控制器和驱动器 IMD RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。