- 您现在的位置：买卖IC网 > PDF目录2002 > LICAL-DEC-MS001 (Linx Technologies Inc)IC DECODER MS SERIES 20-SSOP PDF资料下载
参数资料
| 型号： | LICAL-DEC-MS001 |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 7/24页 |
| 文件大小： | 0K |
| 描述： | IC DECODER MS SERIES 20-SSOP |
| 产品目录绘图： | LICAL-DEC-MS001 Series |
| 标准包装： | 1,600 |
| 系列： | MS |
| 类型： | 数据解码器 |
| 应用： | 警报系统，通信系统 |
| 电压 - 电源，模拟： | 2.0 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
–
11
Deccoder Operation
When the decoder first powers up, it will set the baud rate and check the
state of the RX_CNTL line. If this line is pulled high, then the decoder will go
into Receiver Control Mode. If the line is low, it will go to sleep until a rising
edge (low to high transition) on the DATA_IN line puts it into Receive Mode
or a high signal on the LEARN line puts it into Learn Mode.
Receive Mode
When a rising edge is seen on the DATA_IN line, the decoder enters
Receive Mode. The decoder will begin by looking for a valid packet,
meaning that there are no errors and that the received Code Word matches
one that is saved in memory. If there is a match, then the decoder will
reproduce the states of the encoder’s data lines on its own data lines. It
will also output the ID of the encoder once, on reception of the first valid
packet. It will then look for the next valid data packet. If, at any time, an
error or an unknown Code Word is detected, then the decoder will ignore
the packet and look for the next one.
If the timer runs out, then the decoder will go back to sleep. This time is
dependent upon the baud rate selected by the user. It is 131mS for
2,400bps and 9,600bps, and 65mS for 19,200bps and 28,800bps.
LEARN Mode
In order for the decoder to accept transmissions from an encoder, it must
first learn the encoder’s Code Word. This is done by taking the LEARN
line high to place the decoder into Learn Mode. Once in Learn Mode, the
MODE_IND line will start switching, allowing for connection of a LED to
provide visual indication that the decoder is ready to accept a new Code
Word. This will continue until the LEARN line goes high again, or until a
time-out after 17 seconds.
The decoder will look for a valid transmission from an MS Series encoder.
It can store up to forty Code Words in its memory. If a new encoder is
learned while the memory is full, then the decoder will write the new word
over the first word in memory. The decoder will flash the MODE_IND line
five times as an indication that the memory is full and the next code learned
will overwrite the first. The memory will retain all of the learned Code Words
if power is removed.
相关PDF资料 |
PDF描述 |
|---|---|
| LICAL-ENC-MS001 | IC ENCODER MS SERIES 20-SSOP |
| LICAL-TRC-MT | IC TRANSCODER MT BI-DIR 20-SSOP |
| LT1331CNW#PBF | IC TXRX 5V/3V RS232 28-DIP |
| LT1341CG#TRPBF | IC TXRX 5V RS232 SHUTDOWN 28SSOP |
| LT1342CG | IC TXRX 5V RS232 W/3VLOGC 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LICAL-EDC-DS001 | 功能描述:编码器、解码器、复用器和解复用器 DS Series Module Encoder/Decoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| LICAL-ENC-HS001 | 功能描述:编码器、解码器、复用器和解复用器 HS Series Encoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| LICAL-ENC-HS0011 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:HS SERIES ENCODER DATA GUIDE |
| LICAL-ENC-LS001 | 功能描述:编码器、解码器、复用器和解复用器 LS Series Encoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| LICAL-ENC-MS001 | 功能描述:编码器、解码器、复用器和解复用器 MS Series Encoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。