- 您现在的位置：买卖IC网 > PDF目录2002 > LICAL-DEC-MS001 (Linx Technologies Inc)IC DECODER MS SERIES 20-SSOP PDF资料下载
参数资料
| 型号： | LICAL-DEC-MS001 |
| 厂商： | Linx Technologies Inc |
| 文件页数： | 9/24页 |
| 文件大小： | 0K |
| 描述： | IC DECODER MS SERIES 20-SSOP |
| 产品目录绘图： | LICAL-DEC-MS001 Series |
| 标准包装： | 1,600 |
| 系列： | MS |
| 类型： | 数据解码器 |
| 应用： | 警报系统，通信系统 |
| 电压 - 电源，模拟： | 2.0 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SSOP（0.209"，5.30mm 宽） |
| 供应商设备封装： | 20-SSOP |
| 包装： | 管件 |
–
13
the line to ground while trying to power down the receiver. This mode is
appropriate for receivers that have a high internal pull-up resistance, such
as those offered by Linx. If the intended receiver does not have a pull-up,
then a 100k
Ω or larger resistor to V
CC can be added to the RX_CNTL line to
activate this mode.
TX ID
The TX_ID line will output an eight-bit binary number to identify which
learned encoder sent the transmission. The number is output at the baud
rate set by the SEL_BAUD lines and will normally correspond to the order in
which the decoder learned the encoder, so the first encoder learned will get
number ‘1’, the second will get number ‘2’, and so on. An exception arises
when the memory is full, in which case the first numbers are overwritten as
described in the Learn Mode section. Application Note AN-00156 shows
some example software to read the TX_ID and associate it with a particular
encoder. The C and Visual Basic code is well documented so that it can be
modified for a specific application.
System Example
The first step in using the decoder is to set the baud rate and determine if
the outputs should be latched or momentary. Next, the decoder will need
to learn the encoder’s Code Word. This is done by momentarily pressing
the button connected to the LEARN line. The LED connected to the
MODE_IND line will begin to flash to indicate that the decoder is ready to
learn a new Code Word. One of the buttons on the transmitter is pressed
to send a signal to the decoder. Once this is done, the LEARN button is
pressed again to exit Learn Mode.
Now, when a button is pressed on the encoder, the corresponding line on
the decoder will activate. If the LATCH line is high, the data line will remain
high until the encoder button is pressed again, telling the decoder to pull
the line low.
To clear the memory of the decoder, the LEARN button is pressed and
held for ten seconds, until the LED turns off. Once the button is released,
the LED will light for two seconds to indicate that the memory has been
cleared.
相关PDF资料 |
PDF描述 |
|---|---|
| LICAL-ENC-MS001 | IC ENCODER MS SERIES 20-SSOP |
| LICAL-TRC-MT | IC TRANSCODER MT BI-DIR 20-SSOP |
| LT1331CNW#PBF | IC TXRX 5V/3V RS232 28-DIP |
| LT1341CG#TRPBF | IC TXRX 5V RS232 SHUTDOWN 28SSOP |
| LT1342CG | IC TXRX 5V RS232 W/3VLOGC 28SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LICAL-EDC-DS001 | 功能描述:编码器、解码器、复用器和解复用器 DS Series Module Encoder/Decoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| LICAL-ENC-HS001 | 功能描述:编码器、解码器、复用器和解复用器 HS Series Encoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| LICAL-ENC-HS0011 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:HS SERIES ENCODER DATA GUIDE |
| LICAL-ENC-LS001 | 功能描述:编码器、解码器、复用器和解复用器 LS Series Encoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| LICAL-ENC-MS001 | 功能描述:编码器、解码器、复用器和解复用器 MS Series Encoder RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。