- 您现在的位置：买卖IC网 > PDF目录98000 > LIS1R02 (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PDSO24 PDF资料下载
参数资料
| 型号： | LIS1R02 |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO24 |
| 封装： | SO-24 |
| 文件页数： | 7/11页 |
| 文件大小： | 81K |
| 代理商： | LIS1R02 |
5/11
LIS1R02 (L6671)
SERIAL PORT, REGISTERS, EPROM and TEST MODES
1.0 SERIAL PORT
1.1 READ & WRITE REGISTERS
Figure 2.
SPE is the Serial Port Enable. It goes high at the start of the transmission and goes back low at the end. SPC
is the Serial Port Clock. It is stopped high when SPE is low (no transmission). SPD is the Serial Port Data. It is
driven by the falling edge of SPC. It should be captured at the rising edge of SPC.
The Read Register or Write Register command consists of 16 clocks or bit. A bit duration is the time between
two falling edges of SPC. The first bit (bit 0) starts at the first falling edge of SPC after the rising edge of SPE
and the last bit (bit 15) starts at the last falling edge of SPC just before the falling edge of SPE.
s
bit 0 : RW bit. When 0, the data (D7:0) is written into the device. When 1, the data (D7:0) from the device
is read. In this case, the LIS1R02 will drive SPD at the start of bit 8.
s
bit 1-3 : chip ID. The chip ID for the LIS1R02 is ID(2:0)=110. The device accepts the command only
when the ID is valid (equal to 110).
s
bit 4-7 : address AD(3:0). This is the address field for the registers. See section 2 for more details.
s
bit 8-15 : data D(7:0). This is the data that will be written (read) into (from) the register whose address
is AD(3:0).
1.2 READ FIFO
Figure 3.
The Read FIFO command consists of 24 clocks or bits.
bit 0 : READ bit. The value is 1.
bit 1-3 : chip ID. ID(2:0)=110.
bit 4-7 : FIFO address.
bit 8-23: FIFO data.
SPE
SPC
SPD
RW
ID2
ID1
ID0
AD3
AD2
AD1
AD0
D7
D6
D5
D4
D3
D2
D1
D0
D00IN1119
SPE
SPC
SPD
RW
ID2
ID1
ID0
AD3
AD2
AD1
AD0
D7-0
D6-0
.....
D0-0
D7-1
D6-1
.....
D0-1
D00IN1120
相关PDF资料 |
PDF描述 |
|---|---|
| LIS35DE | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| LIS35DETR | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| LIS3L02AQ3TR | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L02AQ3 | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L06AL | SPECIALTY ANALOG CIRCUIT, PBGA8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS202DL | 功能描述:加速计 - 板上安装 ULTRA LOW POWER 2 AXES LIN/ACCELEROMTR RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS202DLTR | 功能描述:加速计 - 板上安装 ULTRA COMPACT LOW POWER 2 AXES LIN A RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS244AL | 功能描述:加速计 - 板上安装 MEMS MOTION SENSOR 2-AXIS RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS244ALH | 功能描述:加速计 - 板上安装 MEMS Inertial High Pef 2-Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS244ALHTR | 功能描述:加速计 - 板上安装 MEMS Inertial High Pef 2-Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。