- 您现在的位置：买卖IC网 > PDF目录79906 > LIS33DETR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF资料下载
参数资料
| 型号： | LIS33DETR |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封装： | 3 X 3 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件页数： | 17/31页 |
| 文件大小： | 532K |
| 代理商： | LIS33DETR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
Register description
LIS33DE
24/31
Doc ID 15596 Rev 1
7.2
CTRL_REG2 (21h)
Table 18.
CTRL_REG2 (21h) register
Table 19.
CTRL_REG2 (21h) register description
SIM bit selects the SPI serial interface mode. When SIM is ‘0’ (default value) the 4-wire
interface mode is selected. The data coming from the device are sent to SDO pad. In 3-wire
interface mode output data are sent to SDA_SDI pad.
BOOT bit is used to refresh the content of internal registers stored in the flash memory
block. At the device power up the content of the flash memory block is transferred to the
internal registers related to trimming functions to permit a good behavior of the device itself.
If for any reason the content of trimming registers is changed it is sufficient to use this bit to
restore correct values. When BOOT bit is set to ‘1’ the content of internal flash is copied
inside corresponding internal registers and it is used to calibrate the device. These values
are factory trimmed and they are different for every accelerometer. They permit a good
behavior of the device and normally they have not to be changed. At the end of the boot
process the BOOT bit is set again to ‘0’.
7.3
CTRL_REG3 [Interrupt CTRL register] (22h)
SIM
BOOT
0(1)
1.
Bit to be kept to “0” for correct device functionality.
0(1)
SIM
SPI serial interface mode selection. Default value: 0
(0: 4-wire interface; 1: 3-wire interface)
BOOT
Reboot memory content. Default value: 0
(0: normal mode; 1: reboot memory content)
Table 20.
CTRL_REG3 (22h) register
IHL
0(1)
1.
Bit to be kept to “0” for correct push-pull on Interrupt pad (INT).
0(2)
2.
Bit to be kept to “0” for correct device functionality.
0(2)
ICFG2
ICFG1
ICFG0
Table 21.
CTRL_REG3 (22h) register description
IHL
Interrupt active high, low. Default value 0.
(0: active high; 1: active low)
ICFG2-
ICFG0
Data signal on INT pad control bits. Default value 000.
(see table below)
相关PDF资料 |
PDF描述 |
|---|---|
| LSN2-T/10-W3N-C | 1-OUTPUT 33 W DC-DC REG PWR SUPPLY MODULE |
| LM2576-5.0WUTR | 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSSO5 |
| LS4301-7ERD0T | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LS5660-7EPD7TB1 | 2-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
| LTC3615IUF#TRPBF | SWITCHING REGULATOR, PQCC24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS344AL | 功能描述:加速计 - 板上安装 MEMS Sensor RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS344ALH | 功能描述:加速计 - 板上安装 MEMS Inertial High Pef 3-Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS344ALH_0804 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS inertial sensor high performance 3-axis 【2/【6g ultracompact linear accelerometer |
| LIS344ALHTR | 功能描述:加速计 - 板上安装 MEMS Inertial High Pef 3-Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS344ALHTR-CUT TAPE | 制造商:ST 功能描述:LIS344ALH Series 3 Axis Digital High Performance MEMS Inertial Sensor - LGA-16L |
发布紧急采购，3分钟左右您将得到回复。