- 您现在的位置：买卖IC网 > PDF目录43919 > LIS3DH (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF资料下载
参数资料
| 型号： | LIS3DH |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封装： | 3 X 3 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件页数： | 8/42页 |
| 文件大小： | 689K |
| 代理商： | LIS3DH |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页
Terminology and functionality
LIS3DH
16/42
Doc ID 17530 Rev 1
3.2.2
Self-test
Self-test allows to check the sensor functionality without moving it. The self-test function is
off when the self-test bit (ST) is programmed to ‘0‘. When the self-test bit is programmed to
‘1‘ an actuation force is applied to the sensor, simulating a definite input acceleration. In this
case the sensor outputs exhibit a change in their DC levels which are related to the selected
full scale through the device sensitivity. When self-test is activated, the device output level is
given by the algebraic sum of the signals produced by the acceleration acting on the sensor
and by the electrostatic test-force. If the output signals change within the amplitude
specified inside Table 3, then the sensor is working properly and the parameters of the
interface chip are within the defined specifications.
3.2.3
6D / 4D orientation detection
The LIS3DH include 6D / 4D orientation detection.
6D / 4D orientation recognition: In this configuration the interrupt is generated when the
device is stable in a known direction. In 4D configuration Z axis position detection is disable.
3.3
Sensing element
A proprietary process is used to create a surface micro-machined accelerometer. The
technology allows carrying out suspended silicon structures which are attached to the
substrate in a few points called anchors and are free to move in the direction of the sensed
acceleration. To be compatible with the traditional packaging techniques a cap is placed on
top of the sensing element to avoid blocking the moving parts during the moulding phase of
the plastic encapsulation.
When an acceleration is applied to the sensor the proof mass displaces from its nominal
position, causing an imbalance in the capacitive half-bridge. This imbalance is measured
using charge integration in response to a voltage pulse applied to the capacitor.
At steady state the nominal value of the capacitors are few pF and when an acceleration is
applied the maximum variation of the capacitive load is in the fF range.
3.4
IC interface
The complete measurement chain is composed by a low-noise capacitive amplifier which
converts the capacitive unbalancing of the MEMS sensor into an analog voltage that is
finally available to the user by an analog-to-digital converter.
The acceleration data may be accessed through an I2C/SPI interface thus making the
device particularly suitable for direct interfacing with a microcontroller.
The LIS3DH features a Data-Ready signal (RDY) which indicates when a new set of
measured acceleration data is available thus simplifying data synchronization in the digital
system that uses the device.
The LIS3DH may also be configured to generate an inertial Wake-Up and Free-Fall interrupt
signal accordingly to a programmed acceleration event along the enabled axes. Both Free-
Fall and Wake-Up can be available simultaneously on two different pins.
相关PDF资料 |
PDF描述 |
|---|---|
| LIS3L02AL | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS3L02ALTR | SPECIALTY ANALOG CIRCUIT, PBGA8 |
| LIS3L02AQ5TR | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L02AQ5 | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LIS3L02AQ | SPECIALTY ANALOG CIRCUIT, QCC44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS3DHHTR | 功能描述:ACCELEROMETER 3-AXIS 16LGA 制造商:stmicroelectronics 系列:MEMS 零件状态:在售 类型:数字 轴:X，Y，Z 加速度范围:±2.5g 灵敏度（LSB/g）:13157（±2.5g） 灵敏度（mV/g）:- 带宽:235Hz ~ 440Hz 输出类型:SPI 电压 - 电源:1.71 V ~ 3.6 V 特性:温度传感器 工作温度:-40°C ~ 85°C（TA） 安装类型:表面贴装 封装/外壳:16-LGA 供应商器件封装:16-CCLGA（5x5） 标准包装:1 |
| LIS3DHTR | 功能描述:加速计 - 板上安装 MEMS Ultra Low-Power 3-Axes "Nano" RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3DSH | 功能描述:加速计 - 板上安装 MEMS 3-Axis Nano 1.71 to 3.6V 1.6kHz RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3DSHTR | 功能描述:加速计 - 板上安装 MEMS 3-Axis Nano 1.71 to 3.6V 1.6kHz RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3L02AL | 功能描述:加速计 - 板上安装 3-axis +/-2g Linear MEMS Intertial Sensr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。