- 您现在的位置：买卖IC网 > PDF目录69004 > LIS3LV02DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF资料下载
参数资料
| 型号： | LIS3LV02DL |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封装： | 4.40 X 7.50 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件页数： | 14/48页 |
| 文件大小： | 681K |
| 代理商： | LIS3LV02DL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
LIS3LV02DL
Application hints
21/48
4
Application hints
Figure 5.
LIS3LV02DL electrical connection
The device core is supplied through Vdd line while the I/O pads are supplied through
Vdd_IO line. Power supply decoupling capacitors (100 nF ceramic, 10
F Al) should be
placed as near as possible to the pin 13 of the device (common design practice).
All the voltage and ground supplies must be present at the same time to have proper
behavior of the IC (refer to Figure 7). It is possible to remove Vdd maintaining Vdd_IO
without blocking the communication busses. In this condition the measurement chain is
powered off.
The functionality of the device and the measured acceleration data is selectable and
accessible through the I2C/SPI interface.When using the I2C, CS must be tied high while
SDO must be left floating. Refer to dedicated application note for further information on
device usage.
The functions, the trasholds and the timing of the interrupt pin (INT) can be completely
programmed by the user through the I2C/SPI interface.
4.1
Soldering Information
The LGA-16 package is compliant with the ECOPACK, RoHS and “Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020C.
Leave “Pin 1 Indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com/mems.
DIRECTION OF THE
DETECTABLE
ACCELERATIONS
Vdd_IO
CS
SC
L
/SP
C
SD
A/
SD
I/S
D
O
SD
O
R
D
Y
/IN
T
10uF
Vdd
Digital signal from/to signal controller.Signal’s levels are defined by proper selection of Vdd_IO
100nF
GND
LIS3LV02DL
(TOP VIEW)
1
6
7
8
9
14
15
16
Y
1
X
Z
相关PDF资料 |
PDF描述 |
|---|---|
| LM10010SD | SWITCHING REGULATOR, PDSO10 |
| LM10010SDX | SWITCHING REGULATOR, PDSO10 |
| LM12L458CIVX | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LM185BYH-MLS | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, MBCY3 |
| LM234H/NOPB | SPECIALTY ANALOG CIRCUIT, MBCY3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS3LV02DL_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS inertial sensor 3-axis - 【2g/【6g digital output low voltage linear accelerometer |
| LIS3LV02DLTR | 功能描述:加速计 - 板上安装 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3LV02DL-TR | 制造商:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR |
| LIS3LV02DQ | 功能描述:加速计 - 板上安装 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3LV02DQ-TR | 功能描述:加速计 - 板上安装 INERTIAL SENSOR Lo Vltg 3Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。