- 您现在的位置：买卖IC网 > PDF目录69004 > LIS3LV02DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF资料下载
参数资料
| 型号： | LIS3LV02DL |
| 厂商： | STMICROELECTRONICS |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封装： | 4.40 X 7.50 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件页数： | 26/48页 |
| 文件大小： | 681K |
| 代理商： | LIS3LV02DL |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Register description
LIS3LV02DL
32/48
PD1, PD0 bit allows to turn the device out of power-down mode. The device is in power-
down mode when PD1, PD0= “00” (default value after boot). The device is in normal mode
when either PD1 or PD0 is set to 1.
DF1, DF0 bit allows to select the data rate at which acceleration samples are produced. The
default value is “00” which corresponds to a data-rate of 40 Hz. By changing the content of
DF1, DF0 to “01”, “10” and “11” the selected data-rate will be set respectively equal to
160 Hz, 640 Hz and to 2560 Hz.
ST bit is used to activate the self test function. When the bit is set to one, an output change
will occur to the device outputs (refer to table 2 and 3 for specification) thus allowing to
check the functionality of the whole measurement chain.
Zen bit enables the Z-axis measurement channel when set to 1. The default value is 1.
Yen bit enables the Y-axis measurement channel when set to 1. The default value is 1.
Xen bit enables the X-axis measurement channel when set to 1. The default value is 1.
7.9
CTRL_REG2 (21h)
ST
Self Test Enable
(0: normal mode; 1: self-test active)
Zen
Z-axis enable
(0: axis off; 1: axis on)
Yen
Y-axis enable
(0: axis off; 1: axis on)
Xen
X-axis enable
(0: axis off; 1: axis on)
Table 31.
Register description (continued) (20h)
Table 32.
Register (21h)
FS
BDU
BLE
BOOT
IEN
DRDY
SIM
DAS
Table 33.
Register description (21h)
FS
Full Scale selection
(0: ±2g; 1: ±6g)
BDU
Block Data Update
(0: continuous update; 1: output registers not updated between MSB and LSB
reading)
BLE
Big/Little Endian selection
(0: little endian; 1: big endian)
BOOT
Reboot memory content
IEN
Interrupt ENable
(0: data ready on RDY pad; 1: interrupt events on RDY pad)
DRDY
Enable Data-Ready generation
相关PDF资料 |
PDF描述 |
|---|---|
| LM10010SD | SWITCHING REGULATOR, PDSO10 |
| LM10010SDX | SWITCHING REGULATOR, PDSO10 |
| LM12L458CIVX | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LM185BYH-MLS | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, MBCY3 |
| LM234H/NOPB | SPECIALTY ANALOG CIRCUIT, MBCY3 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LIS3LV02DL_08 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:MEMS inertial sensor 3-axis - 【2g/【6g digital output low voltage linear accelerometer |
| LIS3LV02DLTR | 功能描述:加速计 - 板上安装 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3LV02DL-TR | 制造商:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR |
| LIS3LV02DQ | 功能描述:加速计 - 板上安装 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
| LIS3LV02DQ-TR | 功能描述:加速计 - 板上安装 INERTIAL SENSOR Lo Vltg 3Axis RoHS:否 制造商:Murata 传感轴:Double 加速:12 g 灵敏度: 封装 / 箱体: 输出类型:Analog 数字输出 - 位数:11 bit 电源电压-最大:5.25 V 电源电压-最小:4.75 V 电源电流:4 mA 最大工作温度:+ 125 C 最小工作温度:- 40 C |
发布紧急采购，3分钟左右您将得到回复。