- 您现在的位置：买卖IC网 > PDF目录240270 > LM25066APSQX (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF资料下载
参数资料
| 型号： | LM25066APSQX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封装： | LLP-24 |
| 文件页数： | 17/48页 |
| 文件大小： | 1658K |
| 代理商： | LM25066APSQX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Option D:
The OVLO function can be disabled by grounding
the OVLO pin. The UVLO thresholds are set as described in
Option B or Option C.
POWER GOOD
When the voltage at the FB pin increases above its threshold,
the internal pull-down acting on the PGD pin is disabled al-
lowing PGD to rise to V
PGD through the pull-up resistor, RPG,
as shown in Figure 14. The pull-up voltage (V
PGD) can be as
high as 17V and can be higher or lower than the voltages at
VIN and OUT. VDD is a convenient choice for V
PGD as it al-
lows interface to low voltage logic and avoids glitching on
PGD during power-up. If a delay is required at PGD, suggest-
C
PG adds delay to the rising edge, but not to the falling edge.
In Figure 15B, the rising edge is delayed by R
PG1 + RPG2 and
C
PG, while the falling edge is delayed a lesser amount by
R
lows for equal delays at the two edges, or a short delay at the
rising edge and a long delay at the falling edge.
Setting the output threshold for the PGD pin requires two re-
sistors (R4, R5) as shown in Figure 13 . While monitoring the
output voltage is shown in Figure 13, R4 can be connected to
any other voltage which requires monitoring.
The resistor values are calculated as follows:
Choose the upper and lower threshold (V
PGDH) and (VPGDL)
at V
OUT.
As an example, assume the application requires the following
thresholds: V
PGDH = 10.14V and VPGDL = 9.9V. Therefore
V
PGD(HYS) = 0.24V. The resistor values are:
R4 = 10 k
, R5 = 1.3 k
Where the R4 and R5 resistor values are known, the threshold
voltages and hysteresis are calculated from the following:
301460a5
FIGURE 13. Programming the PGD Threshold
30146051
FIGURE 14. Power Good Output
www.national.com
24
LM25066A
相关PDF资料 |
PDF描述 |
|---|---|
| LFD24D | 2-OUTPUT 75 W DC-DC REG PWR SUPPLY MODULE |
| LTC695-3.3CN | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP16 |
| LM4040CIM3-10.0 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 10 V, PDSO3 |
| LKP5660-6ERD5TB1 | 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE |
| LKP5660-6ERD7TB1 | 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM25066APSQX/NOPB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM25066EVK/NOPB | 功能描述:电源管理IC开发工具 LM25066 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM25066IAPSQ/NOPB | 制造商:Texas Instruments 功能描述:IC PWR MGMT/PROT PMBUS 24WQFN 制造商:Texas Instruments 功能描述:System PWR Mgmt & Protection IC |
| LM25066IAPSQE/NOPB | 功能描述:热插拔功率分布 System PWR Mgmt & Protection IC RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制:45 mA 电源电压-最大:17 V 电源电压-最小:2.9 V 工作温度范围:- 40 C to + 85 C 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:WQFN-24 封装:Reel |
| LM25066IAPSQX/NOPB | 制造商:Texas Instruments 功能描述:IC PWR MGMT/PROT PMBUS 24WQFN 制造商:Texas Instruments 功能描述:System PWR Mgmt & Protection IC |
发布紧急采购，3分钟左右您将得到回复。