- 您现在的位置：买卖IC网 > PDF目录44546 > LM25066PSQE (NATIONAL SEMICONDUCTOR CORP) POWER SUPPLY SUPPORT CKT, QCC24 PDF资料下载
参数资料
| 型号： | LM25066PSQE |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | POWER SUPPLY SUPPORT CKT, QCC24 |
| 封装： | LLP-24 |
| 文件页数： | 10/48页 |
| 文件大小： | 1456K |
| 代理商： | LM25066PSQE |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
Applications Section
30115801
FIGURE 6. Typical Application Circuit
DESIGN-IN PROCEDURE
(Refer to Figure 6 for Typical Application Circuit) Shown here
is the step-by-step procedure for hardware design of the
LM25066. This procedure refers to section numbers that pro-
vide detailed information on the following design steps. The
recommended design-in procedure is as follows:
MOSFET Selection:
Determine MOSFET value based on
breakdown voltage, current and power ratings.
Current Limit, R
S: Determine the current limit threshold
(I
LIM). This threshold must be higher than the normal maxi-
mum load current, allowing for tolerances in the current sense
resistor value and the LM25066 Current Limit threshold volt-
age. Use equation 1 to determine the value for R
S.
Power Limit Threshold:
Determine the maximum allowable
power dissipation for the series pass MOSFET (Q
1) using the
device’s SOA information. Use equation 2 to determine the
value for R
PWR.
Turn-On Time and TIMER Capacitor, C
T: Determine the
value for the timing capacitor at the TIMER pin (C
T) using
equation 8. The fault timeout period (t
FAULT) MUST be longer
than the circuit’s turn-on-time. The turn-on time can be esti-
mated using the equations in the TURN-ON TIME section of
this data sheet, but should be verified experimentally. Review
the resulting insertion time, and the restart timing if retry is
enabled.
UVLO, OVLO:
Choose option A, B, C, or D from the UVLO,
OVLO section of the Application Information to set the UVLO
and OVLO thresholds and hysteresis. Use the procedure for
the appropriate option to determine the resistor values at the
UVLO/EN and OVLO pins.
Power Good:
Choose the appropriate output voltage and
calculate the required resistor divider from the output voltage
to the FB pin. Choose either VDD or OUT to connect properly
sized pull-up resistor for the Power Good output (PGD).
Refer to Programming Guide section:
After all hardware
design is complete, refer to the programming guide for a step
by step procedure regarding software.
MOSFET SELECTION
It is recommended that the external MOSFET (Q
1) selection
be based on the following criteria:
- The BV
DSS rating should be greater than the maximum sys-
tem voltage (V
SYS), plus ringing and transients which can
occur at V
SYS when the circuit card, or adjacent cards, are
inserted or removed.
- The maximum continuous current rating should be based on
the current limit threshold (e.g. 25 mV/R
S), not the maximum
load current, since the circuit can operate near the current
limit threshold continuously.
- The Pulsed Drain Current spec (I
DM) must be greater than
the current threshold for the circuit breaker function (45 mV/
R
S when CL = CB = GND).
- The SOA (Safe Operating Area) chart of the device and its
thermal properties should be used to determine the maximum
power dissipation threshold set by the R
PWR resistor. The
programmed maximum power dissipation should have a rea-
sonable margin from the maximum power defined by the
MOSFET’s SOA curve (if the device is set to infinitely retry,
the MOSFET will be repeatedly stressed during fault restart
www.national.com
18
LM25066
相关PDF资料 |
PDF描述 |
|---|---|
| LM25066PSQX | POWER SUPPLY SUPPORT CKT, QCC24 |
| LM25066PSQ | POWER SUPPLY SUPPORT CKT, QCC24 |
| LM25574Q0MT | SWITCHING REGULATOR, PDSO16 |
| LM25574Q0MTX | SWITCHING REGULATOR, PDSO16 |
| LM25576Q0MH | SWITCHING REGULATOR, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM25066PSQE/NOPB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM25066PSQX/NOPB | 功能描述:热插拔功率分布 RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| LM25069 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Positive Low Voltage Power Limiting Hot Swap Controller |
| LM25069MM-2EVAL | 功能描述:BOARD EVALUATION LM25069 RoHS:是 类别:编程器，开发系统 >> 评估演示板和套件 系列:- 标准包装:1 系列:PCI Express® (PCIe) 主要目的:接口，收发器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要属性:- 次要属性:- 已供物品:板 |
| LM25069MM-2EVAL/NOPB | 功能描述:电源管理IC开发工具 LM25069MM-2 Eval Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。