参数资料
型号: LM2575T-012G
厂商: ON SEMICONDUCTOR
元件分类: 稳压器
英文描述: 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, SFM5
封装: LEAD FREE, CASE 314D-04, TO-220, 5 PIN
文件页数: 4/28页
文件大小: 492K
代理商: LM2575T-012G
LM2575, NCV2575
http://onsemi.com
12
Procedure (Adjustable Output Version: LM2575Adj) (continued)
Procedure
Example
4. Inductor Selection (L1)
A. Use the following formula to calculate the inductor Volt x
microsecond [V x ms] constant:
B. Match the calculated E x T value with the corresponding
number on the vertical axis of the Inductor Value Selection
Guide shown in Figure 21. This E x T constant is a measure
of the energy handling capability of an inductor and is
dependent upon the type of core, the core area, the number
of turns, and the duty cycle.
C. Next step is to identify the inductance region intersected by
the E x T value and the maximum load current value on the
horizontal axis shown in Figure 21.
D. From the inductor code, identify the inductor value. Then
select an appropriate inductor from the Table 1 or Table 2.
The inductor chosen must be rated for a switching
frequency of 52 kHz and for a current rating of 1.15 x IIoad.
The inductor current rating can also be determined by
calculating the inductor peak current:
where ton is the “on” time of the power switch and
For additional information about the inductor, see the
inductor section in the “External Components” section of
this data sheet.
ExT + Vin Vout
Vout
Von
x 10
6
F[Hz]
[V x ms]
Ip(max) + ILoad(max) )
Vin Vout ton
2L
ton +
Vout
Vin
x 1
fosc
4. Inductor Selection (L1)
A. Calculate E x T [V x ms] constant:
B. E x T = 51 [V x ms]
C. ILoad(max) = 1.0 A
Inductance Region = L220
D. Proper inductor value = 220 mH
Choose the inductor from the Table 1 or Table 2.
ExT + 12 8.0 x 8.0
12
x 1000
52 +
51 [V x ms]
5. Output Capacitor Selection (Cout)
A. Since the LM2575 is a forwardmode switching regulator
with voltage mode control, its open loop 2pole2zero
frequency characteristic has the dominant polepair
determined by the output capacitor and inductor values.
For stable operation, the capacitor must satisfy the
following requirement:
B. Capacitor values between 10 mF and 2000 mF will satisfy
the loop requirements for stable operation. To achieve an
acceptable output ripple voltage and transient response, the
output capacitor may need to be several times larger than
the above formula yields.
C. Due to the fact that the higher voltage electrolytic capacitors
generally have lower ESR (Equivalent Series Resistance)
numbers, the output capacitor’s voltage rating should be at
least 1.5 times greater than the output voltage. For a 5.0 V
regulator, a rating of at least 8V is appropriate, and a 10 V
or 16 V rating is recommended.
Cout w 7.785
Vin(max)
Vout xL[μH]
[μF]
5. Output Capacitor Selection (Cout)
A.
To achieve an acceptable ripple voltage, select
Cout = 100 mF electrolytic capacitor.
Cout w 7.785
12
8.220 +
53 μF
相关PDF资料
PDF描述
LM2577K-12/883 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2
LM2577KADJ/883 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBCY4
LM2577K-15/883 6 A SWITCHING REGULATOR, 62 kHz SWITCHING FREQ-MAX, MBFM2
LM2633MTDX/NOPB SWITCHING CONTROLLER, 275 kHz SWITCHING FREQ-MAX, PDSO48
LM2635MX/NOPB SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO20
相关代理商/技术参数
参数描述
LM2575T-015 功能描述:直流/直流开关调节器 15V 1A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
LM2575T-015G 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:1.0 A, Adjustable Output Voltage, Step−Down Switching Regulator
LM2575T12 制造商:Semtech 功能描述:_
LM2575T-12 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
LM2575T-12 LF03 制造商:National Semiconductor 功能描述:Conv DC-DC Single Step Down 4V to 40V 5-Pin(5+Tab) TO-220 制造商:Texas Instruments 功能描述:Conv DC-DC Single Step Down 4V to 40V 5-Pin(5+Tab) TO-220