- 您现在的位置：买卖IC网 > PDF目录178069 > LM2576 (ON SEMICONDUCTOR) 3.0 A, 15 V, Step-Down Switching Regulator(3.0A,15V,降压型开关稳压器) PDF资料下载
参数资料
| 型号： | LM2576 |
| 厂商： | ON SEMICONDUCTOR |
| 英文描述： | 3.0 A, 15 V, Step-Down Switching Regulator(3.0A,15V,降压型开关稳压器) |
| 中文描述： | 3.0甲，15 V的，降压型开关稳压器（3.0A的，15V的，降压型开关稳压器） |
| 文件页数： | 2/28页 |
| 文件大小： | 275K |
| 代理商： | LM2576 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LM2576
http://onsemi.com
10
Procedure (Fixed Output Voltage Version) In order to simplify the switching regulator design, a stepbystep
design procedure and some examples are provided.
Procedure
Example
Given Parameters:
Vout = Regulated Output Voltage (3.3 V, 5.0 V, 12 V or 15 V)
Vin(max) = Maximum Input Voltage
ILoad(max) = Maximum Load Current
Given Parameters:
Vout = 5.0 V
Vin(max) = 15 V
ILoad(max) = 3.0 A
1. Controller IC Selection
According to the required input voltage, output voltage and
current, select the appropriate type of the controller IC output
voltage version.
1. Controller IC Selection
According to the required input voltage, output voltage,
current polarity and current value, use the LM25765
controller IC
2. Input Capacitor Selection (Cin)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +Vin and ground pin GND. This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value.
2. Input Capacitor Selection (Cin)
A 100
mF, 25 V aluminium electrolytic capacitor located near
to the input and ground pins provides sufficient bypassing.
3. Catch Diode Selection (D1)
A. Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design the diode should have a
current rating equal to the maximum current limit of the
LM2576 to be able to withstand a continuous output short
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A. For this example the current rating of the diode is 3.0 A.
B. Use a 20 V 1N5820 Schottky diode, or any of the
suggested fast recovery diodes shown in Table 1.
4. Inductor Selection (L1)
A. According to the required working conditions, select the
correct inductor value using the selection guide from
B. From the appropriate inductor selection guide, identify the
inductance region intersected by the Maximum Input
Voltage line and the Maximum Load Current line. Each
region is identified by an inductance value and an inductor
code.
C. Select an appropriate inductor from the several different
manufacturers part numbers listed in Table 2.
The designer must realize that the inductor current rating
must be higher than the maximum peak current flowing
through the inductor. This maximum peak current can be
calculated as follows:
where ton is the “on” time of the power switch and
For additional information about the inductor, see the
inductor section in the “Application Hints” section of
this data sheet.
I
p(max)
+ I
Load(max) )
V
in
–Vout ton
2L
ton +
V
out
V
in
x 1.0
fosc
4. Inductor Selection (L1)
A. Use the inductor selection guide shown in Figures 19.
B. From the selection guide, the inductance area intersected
by the 15 V line and 3.0 A line is L100.
C. Inductor value required is 100
mH. From Table 2, choose
an inductor from any of the listed manufacturers.
相关PDF资料 |
PDF描述 |
|---|---|
| LM2742 | N-Channel FET Synchronous Buck Regulator Controller for Low Output Voltages |
| LM2931A | 100 mA, Adjustable Output, LDO Voltage Regulator with 60 V Load Dump Protection(100mA，可调输出，带有60V负载保护的低压差稳压器) |
| LM2931 | 100 mA, Adjustable Output, LDO Voltage Regulator with 60 V Load Dump Protection(100mA，可调输出，带有60V负载保护的低压差稳压器) |
| LM293 | Low Offset Voltage Dual Comparators(低失调电压，2比较器) |
| LM311H | COMPARATOR, 10000 uV OFFSET-MAX, 200 ns RESPONSE TIME, MBCY8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2576/D | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Easy Switcher? 3.0 A Step-Down Voltage Regulator |
| LM2576_05 | 制造商:MICREL 制造商全称:Micrel Semiconductor 功能描述:52kHz Simple 3A Buck Regulator |
| LM2576_06 | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:3.0 A, 15 V, Step−Down Switching Regulator |
| LM2576_11 | 制造商:HTC 制造商全称:HTC Korea TAEJIN Technology Co. 功能描述:3A, 52kHz, Step-Down Switching Regulator |
| LM2576_12 | 制造商:MOTOROLA 制造商全称:Motorola, Inc 功能描述:EASY SWITCHERER 3.0 A STEPa??DOWN VOLTAGE REGULATOR |
发布紧急采购，3分钟左右您将得到回复。