参数资料
型号: LM2576D2TR4-12
厂商: ON SEMICONDUCTOR
元件分类: 稳压器
英文描述: 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSSO5
封装: D2PAK-5
文件页数: 4/28页
文件大小: 275K
代理商: LM2576D2TR4-12
LM2576
http://onsemi.com
12
Procedure (Adjustable Output Version: LM2576ADJ) (continued)
Procedure
Example
4. Inductor Selection (L1)
A. Use the following formula to calculate the inductor Volt x
microsecond [V x
ms] constant:
B. Match the calculated E x T value with the corresponding
number on the vertical axis of the Inductor Value Selection
Guide shown in Figure 22. This E x T constant is a
measure of the energy handling capability of an inductor and
is dependent upon the type of core, the core area, the
number of turns, and the duty cycle.
C. Next step is to identify the inductance region intersected by
the E x T value and the maximum load current value on the
horizontal axis shown in Figure 25.
D. From the inductor code, identify the inductor value. Then
select an appropriate inductor from Table 2.
The inductor chosen must be rated for a switching
frequency of 52 kHz and for a current rating of 1.15 x ILoad.
The inductor current rating can also be determined by
calculating the inductor peak current:
where ton is the “on” time of the power switch and
For additional information about the inductor, see the
inductor section in the “External Components” section of
this data sheet.
ExT
+ V
in
–Vout
Vout
V
in
x
106
F[Hz]
[V x
ms]
I
p(max)
+ I
Load(max) )
V
in
–Vout ton
2L
ton +
Vout
V
in
x 1.0
fosc
4. Inductor Selection (L1)
A. Calculate E x T [V x
ms] constant:
B. E x T = 80 [V x
ms]
C. ILoad(max) = 2.5 A
Inductance Region = H150
D. Proper inductor value = 150
mH
Choose the inductor from Table 2.
ExT
+ (25–8.0) x 8.0
25
x
1000
52
+ 80 [V x ms]
5. Output Capacitor Selection (Cout)
A. Since the LM2576 is a forwardmode switching regulator
with voltage mode control, its open loop 2pole1zero
frequency characteristic has the dominant polepair
determined by the output capacitor and inductor values.
For stable operation, the capacitor must satisfy the
following requirement:
B. Capacitor values between 10
mF and 2000 mF will satisfy
the loop requirements for stable operation. To achieve an
acceptable output ripple voltage and transient response, the
output capacitor may need to be several times larger than
the above formula yields.
C. Due to the fact that the higher voltage electrolytic capacitors
generally have lower ESR (Equivalent Series Resistance)
numbers, the output capacitor’s voltage rating should be at
least 1.5 times greater than the output voltage. For a 5.0 V
regulator, a rating of at least 8.0 V is appropriate, and a 10 V
or 16 V rating is recommended.
C
out w
13, 300
V
in(max)
Vout xL [μH]
[
μF]
5. Output Capacitor Selection (Cout)
A.
To achieve an acceptable ripple voltage, select
Cout = 680 mF electrolytic capacitor.
C
out w
13, 300 x
25
8 x 150
+ 332.5 μF
相关PDF资料
PDF描述
LM2576TV-12G 7.5 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PZFM5
LM2596-12MWC 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2596-ADJMWC 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2596-ADJMDC 7.5 A SWITCHING REGULATOR, 173 kHz SWITCHING FREQ-MAX, UUC
LM2601MDC 1-CHANNEL POWER SUPPLY SUPPORT CKT, UUC
相关代理商/技术参数
参数描述
LM2576D2TR4-3.3 功能描述:直流/直流开关调节器 3.3V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
LM2576D2TR4-3.3G 功能描述:直流/直流开关调节器 3.3V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
LM2576D2TR4-3.3G-CUT TAPE 制造商:ON 功能描述:LM2576 Series 40 V 3 A 52 kHz Step-Down Switching Regulator - D2PAK-5
LM2576D2TR4-5G 功能描述:直流/直流开关调节器 5V 3A Buck PWM RoHS:否 制造商:International Rectifier 最大输入电压:21 V 开关频率:1.5 MHz 输出电压:0.5 V to 0.86 V 输出电流:4 A 输出端数量: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:PQFN 4 x 5
LM2576DP-12 制造商:HTC 制造商全称:HTC Korea TAEJIN Technology Co. 功能描述:3A, 52kHz, Step-Down Switching Regulator