- 您现在的位置：买卖IC网 > PDF目录14683 > LM2594DADJR2G (ON Semiconductor)IC REG BUCK ADJ 0.5A 8SOIC PDF资料下载
参数资料
| 型号： | LM2594DADJR2G |
| 厂商： | ON Semiconductor |
| 文件页数： | 9/25页 |
| 文件大小： | 0K |
| 描述： | IC REG BUCK ADJ 0.5A 8SOIC |
| 标准包装： | 2,500 |
| 类型： | 降压（降压） |
| 输出类型： | 可调式 |
| 输出数： | 1 |
| 输出电压： | 1.23 V ~ 37 V |
| 输入电压： | 4.5 V ~ 40 V |
| PWM 型： | 电压模式 |
| 频率 - 开关： | 150kHz |
| 电流 - 输出： | 500mA |
| 同步整流器： | 无 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 8-SOICN |
| 其它名称： | LM2594DADJR2G-ND LM2594DADJR2GOSTR |
LM2594
PROCEDURE (ADJUSTABLE OUTPUT VERSION: LM2594)
Procedure
Given Parameters:
V out = Regulated Output Voltage
V in(max) = Maximum DC Input Voltage
I Load(max) = Maximum Load Current
1. Programming Output Voltage
To select the right programming resistor R1 and R2 value (see
Example
Given Parameters:
V out = 5.0 V
V in(max) = 12 V
I Load(max) = 0.5 A
1. Programming Output Voltage (selecting R1 and R2)
Select R1 and R2:
V out + V
1.0 )
V out + 1.23 1.0 )
V out
R2 + R1 * 1.0
ref
+ * 1.0
Figure 1) use the following formula:
R2
ref R1 where V ref = 1.23 V
Resistor R1 can be between 1.0 k and 5.0 k W . (For best
temperature coefficient and stability with time, use 1% metal
V
R2
R1
Select R1 = 1.0 k W
5V
1.23 V
film resistors).
R2 + R1
V out
V ref
* 1.0
R2 = 3.0 k W , choose a 3.0k metal film resistor.
2. Input Capacitor Selection (C in )
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +V in and ground pin GND This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value .
For additional information see input capacitor section in the
“Application Information” section of this data sheet.
3. Catch Diode Selection (D1)
A. Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design, the diode should have a
current rating equal to the maximum current limit of the
LM2594 to be able to withstand a continuous output short.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
2. Input Capacitor Selection (C in )
A 68 m F, 50 V aluminium electrolytic capacitor located near
the input and ground pin provides sufficient bypassing.
3. Catch Diode Selection (D1)
A. For this example, a 1.0 A current rating is adequate.
B. For V in = 12 V use a 20 V 1N5817 Schottky diode or
any suggested fast recovery diode in the Table 2.
http://onsemi.com
9
相关PDF资料 |
PDF描述 |
|---|---|
| RMC15DRES-S13 | CONN EDGECARD 30POS .100 EXTEND |
| MC33063AVDR2G | IC REG BUCK BOOST INV ADJ 8SOIC |
| GEC50DRYN-S13 | CONN EDGECARD 100POS .100 EXTEND |
| GEC50DRYH-S13 | CONN EDGECARD 100POS .100 EXTEND |
| GSC15DRTS-S13 | CONN EDGECARD 30POS .100 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM2594HVM-12 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2594HVM-12/NOPB | 功能描述:直流/直流开关转换器 150KHZ 0.5A STEP- DOWN VLTG REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2594HVM-12/NOPB | 制造商:Texas Instruments 功能描述:DC/DC Converter (DC-DC) / Switching Regu |
| LM2594HVM-3.3 | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM2594HVM-3.3/NOPB | 功能描述:直流/直流开关转换器 150KHZ 0.5A STEP- DOWN VLTG REG RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。