- 您现在的位置：买卖IC网 > PDF目录20782 > LM3421MHX/NOPB (National Semiconductor)IC LED DRVR HP CONS CURR 16TSSOP PDF资料下载
参数资料
| 型号： | LM3421MHX/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 14/67页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR HP CONS CURR 16TSSOP |
| 产品培训模块： | LED Design Solutions |
| 标准包装： | 2,500 |
| 系列： | PowerWise® |
| 恒定电流： | 是 |
| 拓扑： | PWM，SEPIC，降压（降压），升压（升压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 主要： | 车载 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 2MHz |
| 电源电压： | 4.5 V ~ 75 V |
| 输出电压： | 3 V ~ 72 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 16-TSSOP（0.173"，4.40mm）裸露焊盘 |
| 供应商设备封装： | 16-TSSOP-EP |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
| 其它名称： | LM3421MHX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
SNVS574E – JULY 2008 – REVISED MAY 2013
The selection of the three resistors (R SNS , R CSH , and R HSP ) is not arbitrary. For matching and noise performance,
the suggested signal current I CSH is approximately 100 μA. This current does not flow in the LEDs and will not
affect either the off-state LED current or the regulated LED current. I CSH can be above or below this value, but
the high-side amplifier offset characteristics may be affected slightly. In addition, to minimize the effect of the
high-side amplifier voltage offset on LED current accuracy, the minimum V SNS is suggested to be 50 mV. Finally,
a resistor (R HSN = R HSP ) should be placed in series with the HSN pin to cancel out the effects of the input bias
current (~10 μA) of both inputs of the high-side sense amplifier.
The sense resistor (R SNS ) can be placed anywhere in the series string of LEDs as long as the voltage at the HSN
and HSP pins (V HSP and V HSN ) satisfies the following conditions.
V HSP < 76V
V HSN > 3.5V
(10)
Typically, for a buck-boost configuration, R SNS is placed at the bottom of the string (LED-) which allows for
greater flexibility of input and output voltage. However, if there is substantial input voltage ripple allowed, it can
help to place R SNS at the top of the string (LED+) which limits the output voltage of the string to:
V O = 76V - V IN
(11)
Note that he CSH pin can also be used as a low-side current sense input regulated to 1.24V. The high-side
sense amplifier is disabled if HSP and HSN are tied to AGND (or V HSN > V HSP ) .
ANALOG DIMMING
The CSH pin can be used to analog dim the LED current by adjusting the current sense voltage (V SNS ). There
are several different methods to adjust V SNS using the CSH pin:
1. External variable resistance : Adjust a potentiometer placed in series with R CSH to vary V SNS .
2. External variable current source: Source current (0 μA to I CSH ) into the CSH pin to adjust V SNS .
Variable Current Source
V REF
Q7
R MAX
Q8
V CC
LM3421/23
Q6
CSH
R ADJ
R BIAS
R CSH
R ADJ
Variable
Resistance
Figure 19. Analog Dimming Circuitry
In general, analog dimming applications require a lower switching frequency to minimize the effect of the leading
edge blanking circuit. As the LED current is reduced, the output voltage and the duty cycle decreases.
Eventually, the minimum on-time is reached. The lower the switching frequency, the wider the linear dimming
range. Figure 19 shows how both CSH methods are physically implemented.
Method 1 uses an external potentiometer in the CSH path which is a simple addition to the existing circuitry.
However, the LEDs cannot dim completely because there is always some resistance causing signal current to
flow. This method is also susceptible to noise coupling at the CSH pin since the potentiometer increases the size
of the signal current loop.
14
Copyright ? 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM3421 LM3421-Q1 LM3423 LM3423-Q1
相关PDF资料 |
PDF描述 |
|---|---|
| ECC07DRYN | CONN EDGECARD 14POS DIP .100 SLD |
| RS3-4809D | CONV DC/DC 3W 36-72VIN +/-09VOUT |
| GEM10DRSN-S288 | CONN EDGECARD 20POS .156 EXTEND |
| EVW020A0A41-HZ | CONVERTER DC/DC 5.0V 20A OUTPUT |
| RS3-4805D | CONV DC/DC 3W 36-72VIN +/-05VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3421Q0 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:N-Channel Controllers for Constant Current LED Drivers |
| LM3421Q0MH | 制造商:NSC 制造商全称:National Semiconductor 功能描述:N-Channel Controllers for Constant Current LED Drivers |
| LM3421Q0MH/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LM3421Q0MHNOPB | 制造商:National Semiconductor 功能描述:LED DRVR 5V/9V/12V/15V/18V/24V 16-Pin TSSOP EP Tube |
| LM3421Q0MHX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:N-Channel Controllers for Constant Current LED Drivers |
发布紧急采购，3分钟左右您将得到回复。