- 您现在的位置：买卖IC网 > PDF目录17193 > LM3423BBLSCSEV/NOPB (National Semiconductor)BOARD EVAL BUCK BOOST LM3423 PDF资料下载
参数资料
| 型号： | LM3423BBLSCSEV/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 12/67页 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL BUCK BOOST LM3423 |
| 标准包装： | 1 |
| 系列： | PowerWise® |
| 电流 - 输出 / 通道： | 700mA |
| 输出及类型： | 1，非隔离 |
| 输入电压： | 10 ~ 70 V |
| 已供物品： | 板，文档 |
| 已用 IC / 零件： | LM3423 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页
SNVS574E – JULY 2008 – REVISED MAY 2013
PREDICTIVE OFF-TIME (PRO) CONTROL
PRO control is used by the LM3421/23 to control I LED . It is a combination of average peak current control and a
one-shot off-timer that varies with input voltage. The LM3421/23 uses peak current control to regulate the
average LED current through an array of HBLEDs. This method of control uses a series resistor in the LED path
to sense LED current and can use either a series resistor in the MosFET path or the MosFET R DS-ON for both
cycle-by-cycle current limit and input voltage feed forward. D is indirectly controlled by changes in both t OFF and
t ON , which vary depending on the operating point.
Even though the off-time control is quasi-hysteretic, the input voltage proportionality in the off-timer creates an
essentially constant switching frequency over the entire operating range for boost and buck-boost topologies.
The buck topology can be designed to give constant ripple over either input voltage or output voltage, however
switching frequency is only constant at a specific operating point .
This type of control minimizes the control loop compensation necessary in many switching regulators, simplifying
the design process. The averaging mechanism in the peak detection control loop provides extremely accurate
LED current regulation over the entire operating range.
PRO control was designed to mitigate “current mode instability” (also called “sub-harmonic oscillation”) found in
standard peak current mode control when operating near or above 50% duty cycles. When using standard peak
current mode control with a fixed switching frequency, this condition is present, regardless of the topology.
However, using a constant off-time approach, current mode instability cannot occur, enabling easier design and
control.
Predictive off-time advantages:
?
?
There is no current mode instability at any duty cycle.
Higher duty cycles / voltage transformation ratios are possible, especially in the boost regulator.
The only disadvantage is that synchronization to an external reference frequency is generally not available.
SWITCHING FREQUENCY
An external resistor (R T ) connected between the RCT pin and the switch node (where D1, Q1, and L1 connect),
in combination with a capacitor (C T ) between the RCT and AGND pins, sets the off-time (t OFF ) as shown in
Figure 16 . For boost and buck-boost topologies, the V IN proportionality ensures a virtually constant switching
frequency (f SW ).
For a buck topology, R T and C T are also used to set t OFF , however the V IN proportionality will not ensure a
constant switching frequency. Instead, constant ripple operation can be achieved. Changing the connection of R T
in Figure 16 from V SW to V IN will provide a constant ripple over varying V IN . Adding a PNP transistor as shown in
The switching frequency is defined:
Buck (Constant Ripple vs. V IN )
f SW =
25 x ( V IN - V O )
R T x C T X V IN
(4)
Buck (Constant Ripple vs. V O )
25 x ( V IN x V O - V O )
R T x C T x V IN
f SW =
2
2
(5)
Boost and Buck-boost
f SW =
25
R T x C T
(6)
For all topologies, the C T capacitor is recommended to be 1 nF and should be located very close to the
LM3421/23.
12
Copyright ? 2008–2013, Texas Instruments Incorporated
Product Folder Links: LM3421 LM3421-Q1 LM3423 LM3423-Q1
相关PDF资料 |
PDF描述 |
|---|---|
| GCA10DRMI-S288 | CONN EDGECARD 20POS .125 EXTEND |
| ESM06DTKN-S288 | CONN EDGECARD 12POS .156 EXTEND |
| RNM-1509S | CONV DC/DC 1W 15VIN 09VOUT |
| T95Z156K025CZSL | CAP TANT 15UF 25V 10% 2910 |
| ESM06DTKH-S288 | CONN EDGECARD 12POS .156 EXTEND |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3423BS2LYEV/NOPB | 功能描述:LED 照明开发工具 LM3423BS2LY EVAL BOARD RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| LM3423MH | 制造商:Texas Instruments 功能描述:LED DRVR 3Segment 5V/9V/12V/15V/18V/24V 20-Pin TSSOP EP Rail 制造商:Texas Instruments 功能描述:LED DRIVER, HI V, 4.5~75V, POWERWISE |
| LM3423MH/NOPB | 功能描述:LED照明驱动器 RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N |
| LM3423MHBKBSTEV | 制造商:Texas Instruments 功能描述:Development Kits And Tools, The Lm3421/23 Are Versatile High Voltage N-Channel Mosfet Controllers For LED Drivers Evaluation Board |
| LM3423MHBKBSTEV/NOPB | 功能描述:BOARD EVAL BUCK BOOST LM3423 RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:PowerWise® 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
发布紧急采购，3分钟左右您将得到回复。