- 您现在的位置：买卖IC网 > PDF目录20804 > LM3445MX/NOPB (National Semiconductor)IC LED DRIVER TRIAC DIMM 14SOIC PDF资料下载
参数资料
| 型号： | LM3445MX/NOPB |
| 厂商： | National Semiconductor |
| 文件页数： | 24/40页 |
| 文件大小： | 0K |
| 描述： | IC LED DRIVER TRIAC DIMM 14SOIC |
| 标准包装： | 2,500 |
| 系列： | PowerWise® |
| 恒定电流： | 是 |
| 拓扑： | PWM，降压（降压） |
| 输出数： | 1 |
| 内部驱动器： | 无 |
| 类型 - 次要： | 高亮度 LED（HBLED） |
| 频率： | 30kHz ~ 1MHz |
| 电源电压： | 8 V ~ 12 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 带卷 (TR) |
| 工作温度： | -40°C ~ 125°C |
| 其它名称： | LM3445MX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
SNVS570L – JANUARY 2009 – REVISED MAY 2013
V VF-CAP =
V AC(MAX)
#stages
2
(26)
This is, of course, if the capacitors chosen have identical capacitance values and split the line voltage equally.
Often a 20% difference in capacitance could be observed between like capacitors. Therefore a voltage rating
margin of 25% to 50% should be considered.
Determining the capacitance value of the valley-fill capacitors:
The valley fill capacitors should be sized to supply energy to the buck converter (V BUCK ) when the input line is
less than its peak divided by the number of stages used in the valley fill (t X ). The capacitance value should be
calculated when the triac is not firing, i.e. when full LED current is being drawn by the LED string. The maximum
power is delivered to the LED string at this time, and therefore the most capacitance will be needed.
30°
150°
V BUCK
t X
t
8.33 ms
0°
180°
Figure 29. Two Stage Valley-Ffill V BUCK Voltage with no TRIAC Dimming
From the above illustration and the equation for current in a capacitor, i = C x dV/dt, the amount of capacitance
needed at V BUCK will be calculated as follows:
At 60Hz, and a valley-fill circuit of two stages, the hold up time (t X ) required at V BUCK is calculated as follows. The
total angle of an AC half cycle is 180° and the total time of a half AC line cycle is 8.33 ms. When the angle of the
AC waveform is at 30° and 150°, the voltage of the AC line is exactly ? of its peak. With a two stage valley-fill
circuit, this is the point where the LED string switches from power being derived from AC line to power being
derived from the hold up capacitors (C7 and C9). 60° out of 180° of the cycle or 1/3 of the cycle the power is
derived from the hold up capacitors (1/3 x 8.33 ms = 2.78 ms). This is equal to the hold up time (dt) from the
above equation, and dv is the amount of voltage the circuit is allowed to droop. From the next section
(“Determining Maximum Number of Series Connected LEDs Allowed”) we know the minimum V BUCK voltage will
be about 45V for a 90V AC to 135V AC line. At 90V AC low line operating condition input, ? of the peak voltage is
64V. Therefore with some margin the voltage at V BUCK can not droop more than about 15V (dv). (i) is equal to
(P OUT /V BUCK ), where P OUT is equal to (V LED x I LED ). Total capacitance (C7 in parallel with C9) can now be
calculated. See DESIGN EXAMPLE for further calculations of the valley-fill capacitors.
Determining Maximum Number of Series Connected LEDs Allowed:
The LM3445 is an off-line buck topology LED driver. A buck converter topology requires that the input voltage
(V BUCK ) of the output circuit must be greater than the voltage of the LED stack (V LED ) for proper regulation. One
must determine what the minimum voltage observed by the buck converter will be before the maximum number
of LEDs allowed can be determined. Two variables will have to be determined in order to accomplish this.
1. AC line operating voltage. This is usually 90V AC to 135V AC for North America. Although the LM3445 can
operate at much lower and higher input voltages a range is needed to illustrate the design process.
2. How many stages are implemented in the valley-fill circuit (1, 2 or 3).
In this example the most common valley-fill circuit will be used (two stages).
24
Product Folder Links: LM3445
Copyright ? 2009–2013, Texas Instruments Incorporated
相关PDF资料 |
PDF描述 |
|---|---|
| NPS 2-T126 0.500 OHM 1% | RES .5 OHM 25W 1% DPAK |
| REC3-4815SRW/H4/A/M | CONV DC/DC 3W 36-72VIN 15VOUT |
| P51-1500-S-S-D-5V-000-000 | SENSOR 1500PSIS 1/4 NPT 5V |
| P51-500-S-E-D-4.5OVP-000-000 | SENSOR 500PSI 3/8-24 UNF .5-4.5V |
| RMW-140/42-1200/ADH-0 | HEAT SHRINK TUBING |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3445TRIACEVAL | 功能描述:BOARD EVAL LM3445MM RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:PowerWise® 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB） 传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| LM3445TRIACEVAL/NOPB | 制造商:Texas Instruments 功能描述:TRIAC Dimmable Offline LED Driver Evaluation Board |
| LM3447 | 制造商:TI 制造商全称:Texas Instruments 功能描述:Phase Dimmable, Primary Side Power Regulated PFC Flyback Controller for LED Lighting |
| LM3447-A19-120VEVM | 功能描述:LED 照明开发工具 LM3447 Eval Mod RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
| LM3447-A19-230VEVM | 功能描述:LED 照明开发工具 LM3447 Eval Mod RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: |
发布紧急采购，3分钟左右您将得到回复。