- 您现在的位置：买卖IC网 > PDF目录44553 > LM3668SD-3.3/NOPB (NATIONAL SEMICONDUCTOR CORP) 2.05 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, DSO12 PDF资料下载
参数资料
| 型号： | LM3668SD-3.3/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 2.05 A DUAL SWITCHING CONTROLLER, 2500 kHz SWITCHING FREQ-MAX, DSO12 |
| 封装： | ROHS COMPLIANT, LLP-12 |
| 文件页数： | 2/20页 |
| 文件大小： | 2497K |
| 代理商： | LM3668SD-3.3/NOPB |
Internal Synchronous Rectification
While in PWM mode, the LM3668 uses an internal MOSFET
as a synchronous rectifier to reduce rectifier forward voltage
drop and associated power loss. Synchronous rectification
provides a significant improvement in efficiency whenever the
output voltage is relatively low compare to the voltage drop
across an ordinary rectifier diode.
PFM Operation
At very light loads, the converter enters PFM mode and op-
erates with reduced switching frequency and supply current
to maintain high efficiency. The part automatically transitions
into PFM mode when either of two following conditions occur
for a duration of 128 or more clock cycles:
A.
The inductor current reaches zero.
B.
The peak inductor current drops below the I
MODE level,
(Typically I
MODE < 45mA + VIN/80 ).
In PFM operation, the compensation circuit in the error am-
plifier is turned off. The error amplifier works as a hysteretic
comparator. The PFM comparator senses the output voltage
via the feedback pin and controls the switching of the output
FETs such that the output voltage ramps between ~0.8% and
~1.6% of the nominal PWM output voltage (Figure 6). If the
output voltage is below the ‘high’ PFM comparator threshold,
the P1 & P2 (Buck mode) or N2 & P1 (Boost mode) power
switches are turned on. It remains on until the output voltage
reaches the ‘high’ PFM threshold or the peak current exceeds
the I
PFM level set for PFM mode. The typical peak current in
PFM mode is: I
PFM = 220mA
Once the P1 ( Buck mode) or N2 ( Boost mode) power switch
is turned off, the N1 & P2 ( Buck mode) or P1 & P2 (Boost
mode) power switches are turned on until the inductor current
ramps to zero. When the zero inductor current condition is
detected, the N1( Buck mode) or P2 ( Boost mode) power
switches are turned off. If the output voltage is below the ‘high’
PFM comparator threshold, the P1 & P2 (Buck mode) or N2
& P1 ( Boost mode) switches are again turned on and the
cycle is repeated until the output reaches the desired level.
Once the output reaches the ‘high’ PFM threshold, the N1 &
P2 (Buck mode) or P1 & P2 ( Boost mode) switches are turned
on briefly to ramp the inductor current to zero and then both
output switches are turned off and the part enters an ex-
tremely low power mode. Quiescent supply current during this
‘sleep’ mode is 45A (typ), which allows the part to achieve
high efficiency under extremely light load conditions.
20191413
FIGURE 6. PFM to PWM Mode Transition
In addition to the auto mode transition, the LM3668 operates
in PFM Buck or PFM Boost based on the following conditions.
There is a small delta (~500mV) known as dv1(~200mV) &
dv2(~300mV) when V
OUT_TARGET is very close to VIN where
the LM3668 can be in either buck or boost mode. For example
when V
OUT_TARGET = 3.3V and VIN is between 3.1V & 3.6V,
the LM3668 can be in either mode depending on the V
IN vs
V
OUT_TARGET .
Region I: If V
IN < VOUT_TARGET - dv1, the regulator operates
in boost mode.
Region II: If V
OUT_TARGET - dv1 < VIN < VOUT_TARGET+
dv2 ,the regulator operates in either buck or boost mode.
Region III: If V
IN > VOUT_TARGET + dv2, the regulator
operates in buck mode.
20191414
FIGURE 7. V
OUT vs VIN Transition
www.national.com
10
LM3668
相关PDF资料 |
PDF描述 |
|---|---|
| LM368N-5.0 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 5 V, PDIP8 |
| LM3691TLX-1.1 | 1.7 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, PBGA6 |
| LM3691TL-0.85 | 1.7 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, PBGA6 |
| LM3691TLX-3.3 | 1.7 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, PBGA6 |
| LM3691TL-1.0 | 1.7 A SWITCHING REGULATOR, 4400 kHz SWITCHING FREQ-MAX, PBGA6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM3668SD-4550 | 制造商:Texas Instruments 功能描述:Conv DC-DC Single Non-Inv/Inv/Step Up/Step Down 2.5V to 5.5V 12-Pin LLP EP T/R |
| LM3668SD-4550/NOPB | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| LM3668SD-4550EV | 功能描述:电源管理IC开发工具 LM3668SD-4550 EVAL BOARD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM3668SDX-2833 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:1A, High Efficiency Dual Mode Single Inductor Buck-Boost DC/DC Converter |
| LM3668SDX-2833/NOPB | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。