- 您现在的位置：买卖IC网 > PDF目录32307 > LM4873LQX/NOPB (NATIONAL SEMICONDUCTOR CORP) 3 W, 2 CHANNEL, AUDIO AMPLIFIER, QCC24 PDF资料下载
参数资料
| 型号： | LM4873LQX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 3 W, 2 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| 封装： | LLP-24 |
| 文件页数： | 6/25页 |
| 文件大小： | 963K |
| 代理商： | LM4873LQX/NOPB |
Application Information (Continued)
power. The LM4873LQ achieves the same output power
level without forced air cooling. In all circumstances and
conditions, the junction temperature must be held below
150C to prevent activating the LM4873’s thermal shutdown
protection. The LM4873’s power de-rating curve in the Typi-
cal Performance Characteristics shows the maximum
power dissipation versus temperature. Example PCB layouts
for the exposed-DAP TSSOP and LQ packages are shown in
the Demonstration Board Layout section. Further detailed
and specific information concerning PCB layout, fabrication,
and mounting an LQ (LLP) package is available from Na-
tional Semiconductor’s AN1187.
PCB LAYOUT AND SUPPLY REGULATION
CONSIDERATIONS FOR DRIVING 3
AND 4 LOADS
Power dissipated by a load is a function of the voltage swing
across the load and the load’s impedance. As load imped-
ance decreases, load dissipation becomes increasingly de-
pendent on the interconnect (PCB trace and wire) resistance
between the amplifier output pins and the load’s connec-
tions. Residual trace resistance causes a voltage drop,
which results in power dissipated in the trace and not in the
load as desired. For example, 0.1
trace resistance reduces
the output power dissipated by a 4
load from 2.1W to 2.0W.
This problem of decreased load dissipation is exacerbated
as load impedance decreases. Therefore, to maintain the
highest load dissipation and widest output voltage swing,
PCB traces that connect the output pins to a load must be as
wide as possible.
Poor power supply regulation adversely affects maximum
output power. A poorly regulated supply’s output voltage
decreases with increasing load current. Reduced supply
voltage causes decreased headroom, output signal clipping,
and reduced output power. Even with tightly regulated sup-
plies, trace resistance creates the same effects as poor
supply regulation. Therefore, making the power supply
traces as wide as possible helps maintain full output voltage
swing.
BRIDGE CONFIGURATION EXPLANATION
As shown in Figure 2, the LM4873 consists of two pairs of
operational amplifiers, forming a two-channel (channel A and
channel B) stereo amplifier. (Though the following discusses
channel A, it applies equally to channel B.) External resistors
R
f and Ri set the closed-loop gain of Amp1A, whereas two
internal 20k
resistors set Amp2A’s gain at 1. The LM4873
drives a load, such as a speaker, connected between the two
amplifier outputs, OUTA and +OUTA.
Figure 2 shows that Amp1A’s output serves as Amp2A’s
input. This results in both amplifiers producing signals iden-
tical in magnitude, but 180 out of phase. Taking advantage
of this phase difference, a load is placed between OUTA
and +OUTA and driven differentially (commonly referred to
as “bridge mode”). This results in a differential gain of
A
VD =2 * (Rf/R i)
(1)
Bridge mode amplifiers are different from single-ended am-
plifiers that drive loads connected between a single amplifi-
er’s output and ground. For a given supply voltage, bridge
10099331
* Refer to the section Selecting Proper External Components, for a detailed discussion of CB size.
FIGURE 2. Typical Audio Amplifier Application Circuit
Pin out shown for the 28-pin Expoased-DAP TSSOP package. Refer to the Connection Diagrams for the pin out of the
20-pin Exposed-DAP TSSOP, Exposed-DAP LLP, and micro SMD package.
LM4873
www.national.com
14
相关PDF资料 |
PDF描述 |
|---|---|
| LM4891MMX/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4891MX/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4891LDX/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| LM4898MMXNPAU | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| LM4898ITLX/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4873MT | 制造商:Texas Instruments 功能描述: |
| LM4873MT/NOPB | 功能描述:IC AMP AUDIO PWR 3W STER 20TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
| LM4873MTE | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM4873MTE/NOPB | 功能描述:音频放大器 Dual 2.1W Audio Amp Plus Stereo HdPh Fcn RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4873MTE-1 | 功能描述:IC AMP AUDIO PWR 3W STER 28TSSOP RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:H 类 输出类型:耳机，2-通道（立体声） 在某负载时最大输出功率 x 通道数量:35mW x 2 @ 16 欧姆 电源电压:1.62 V ~ 1.98 V 特点:I²C，麦克风，静音，短路保护，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。