- 您现在的位置：买卖IC网 > PDF目录30754 > LM4879IBPX/NOPB (NATIONAL SEMICONDUCTOR CORP) 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 PDF资料下载
参数资料
| 型号： | LM4879IBPX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 音频／视频放大 |
| 英文描述： | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| 封装： | MO-211BC, MICRO, SMD-8 |
| 文件页数： | 13/25页 |
| 文件大小： | 793K |
| 代理商： | LM4879IBPX/NOPB |
Application Information (Continued)
PCB LAYOUT GUIDELINES
This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
"rule-of-thumb" recommendations and the actual results will
depend heavily on the final layout.
General Mixed Signal Layout Recommendation
Power and Ground Circuits
For 2 layer mixed signal design, it is important to isolate the
digital power and ground trace paths from the analog power
and ground trace paths. Star trace routing techniques (bring-
ing individual traces back to a central point rather than daisy
chaining traces together in a serial manner) can have a
major impact on low level signal performance. Star trace
routing refers to using individual traces to feed power and
ground to each circuit or even device. This technique will
take require a greater amount of design time but will not
increase the final price of the board. The only extra parts
required may be some jumpers.
Single-Point Power / Ground Connections
The analog power traces should be connected to the digital
traces through a single point (link). A "Pi-filter" can be helpful
in minimizing high frequency noise coupling between the
analog and digital sections. It is further recommended to put
digital and analog power traces over the corresponding digi-
tal and analog ground traces to minimize noise coupling.
Placement of Digital and Analog Components
All digital components and high-speed digital signals traces
should be located as far away as possible from analog
components and circuit traces.
Avoiding Typical Design / Layout Problems
Avoid ground loops or running digital and analog traces
parallel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.
LM4879
www.national.com
20
相关PDF资料 |
PDF描述 |
|---|---|
| LM4879IBP/NOPB | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA8 |
| LM4879ITLX/NOPB | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PBGA9 |
| LM4880-D08-T | 0.35 W, 2 CHANNEL, AUDIO AMPLIFIER, PDIP8 |
| LM4880-SH2-R | 0.35 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4880-SH2-T | 0.35 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM4879ITL | 制造商:Texas Instruments 功能描述:AMP AUDIO BOOMER 1.1W SMD BUMP-9 |
| LM4879ITL/NOPB | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4879ITLX | 制造商:NSC 制造商全称:National Semiconductor 功能描述:1.1 Watt Audio Power Amplifier |
| LM4879ITLX/NOPB | 功能描述:音频放大器 RoHS:否 制造商:STMicroelectronics 产品:General Purpose Audio Amplifiers 输出类型:Digital 输出功率: THD + 噪声: 工作电源电压:3.3 V 电源电流: 最大功率耗散: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:TQFP-64 封装:Reel |
| LM4879ITP | 功能描述:IC AMP AUDIO PWR 1.1W MONO 8USMD RoHS:是 类别:集成电路 (IC) >> 线性 - 音頻放大器 系列:Boomer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:DirectDrive® 类型:D 类 输出类型:1-通道（单声道），带立体声耳机 在某负载时最大输出功率 x 通道数量:930mW x 1 @ 8 欧姆; 40mW x 2 @ 16 欧姆 电源电压:2.7 V ~ 5.5 V 特点:消除爆音，差分输入，I²C，静音，关闭，音量控制 安装类型:表面贴装 供应商设备封装:25-WLP（2.09x2.09） 封装/外壳:25-WFBGA，WLCSP 包装:带卷 (TR) 其它名称:MAX97000EWA+T-ND |
发布紧急采购，3分钟左右您将得到回复。