- 您现在的位置：买卖IC网 > PDF目录98001 > LM5010AMHE (NATIONAL SEMICONDUCTOR CORP) 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO14 PDF资料下载
参数资料
| 型号： | LM5010AMHE |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 1.5 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO14 |
| 封装： | TSSOP-14 |
| 文件页数： | 4/18页 |
| 文件大小： | 406K |
| 代理商： | LM5010AMHE |
20153822
FIGURE 5. Inductor Current
To keep the circuit in continuous conduction mode, the max-
imum allowed ripple current is twice the minimum load cur-
rent, or 400 mAp-p. Using this value of ripple current, the
inductor (L1) is calculated using the following:
(11)
where F
S(min) is the minimum frequency of 154 kHz (205 kHz
- 25%) at V
IN(max).
This provides a minimum value for L1 - the next higher stan-
dard value (100 H) will be used. To prevent saturation, and
possible destructive current levels, L1 must be rated for the
peak current which occurs if the current limit and maximum
ripple current are reached simultaneously (I
PK in Figure 4).
The maximum ripple amplitude is calculated by re-arranging
Equation 11 using V
IN(max), FS(min), and the minimum inductor
value, based on the manufacturer’s tolerance. Assume, for
this exercise, the inductor’s tolerance is ±20%.
(12)
I
PK = ILIM + IOR(max) = 1.5A + 0.372A = 1.872A
where I
LIM is the maximum guaranteed current limit threshold.
At the nominal maximum load current of 1.0A, the peak in-
ductor current is 1.186A.
R
CL: Since it is obvious that the lower peak of the inductor
current waveform does not exceed 1.0A at maximum load
current (see Figure 5), it is not necessary to increase the cur-
rent limit threshold. Therefore R
CL is not needed for this
exercise. For applications where the lower peak exceeds
1.0A, see the section entitled Increasing The Current Limit
Threshold.
C1:
This capacitor limits the ripple voltage at VIN resulting
from the source impedance of the supply feeding this circuit,
and the on/off nature of the switch current into VIN. At maxi-
mum load current, when the buck switch turns on, the current
into VIN steps up from zero to the lower peak of the inductor
current waveform (I
PK- in Figure 5), ramps up to the peak val-
ue (I
PK+), then drops to zero at turn-off. The average current
into VIN during this on-time is the load current. For a worst
case calculation, C1 must supply this average current during
the maximum on-time. The maximum on-time is calculated at
V
IN = 6V using Equation 5, with a 25% tolerance added:
The voltage at VIN should not be allowed to drop below 5.5V
in order to maintain V
CC above its UVLO.
Normally a lower value can be used for C1 since the above
calculation is a worst case calculation which assumes the
power source has a high source impedance. A quality ceramic
capacitor with a low ESR should be used for C1.
C2 and R3:
Since the LM5010A requires a minimum of 25
mVp-p of ripple at the FB pin for proper operation, the required
ripple at V
OUT is increased by R1 and R2, and is equal to:
V
RIPPLE = 25 mVp-p x (R1 + R2)/R2 = 50 mVp-p
This necessary ripple voltage is created by the inductor ripple
current acting on C2’s ESR + R3. First, the minimum ripple
current, which occurs at minimum VIN, maximum inductor
value, and maximum frequency, is determined.
(13)
The minimum ESR for C2 is then equal to:
If the capacitor used for C2 does not have sufficient ESR, R3
is added in series as shown in the Block Diagram. The value
chosen for C2 is application dependent, and it is recommend-
ed that it be no smaller than 3.3 F. C2 affects the ripple at
V
OUT, and transient response. Experimentation is usually nec-
essary to determine the optimum value for C2.
www.national.com
12
LM5010A/LM5010AQ
相关PDF资料 |
PDF描述 |
|---|---|
| LM5021NA-2/NOPB | 0.7 A SWITCHING CONTROLLER, 560 kHz SWITCHING FREQ-MAX, PDIP8 |
| LM5041BSDX | SWITCHING CONTROLLER, 685 kHz SWITCHING FREQ-MAX, DSO16 |
| LM555H-MLS/NOPB | PULSE; RECTANGULAR, TIMER, MBCY8 |
| LM565MDC | PHASE LOCKED LOOP, UUC |
| LM78CCVFX-J | SPECIALTY ANALOG CIRCUIT, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM5010AMHE/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM5010AMHX | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM5010AMHX/NOPB | 功能描述:直流/直流开关转换器 RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
| LM5010AQ0MH | 制造商:Texas Instruments 功能描述:IC, V REG, 1A, STEP DOWN, 14TSSOP 制造商:Texas Instruments 功能描述:IC, V REG, 1A, STEP DOWN, 14TSSOP; Primary Input Voltage:75V; No. of Outputs:1; Output Voltage:70V; Output Current:1A; Voltage Regulator Case Style:TSSOP; No. of Pins:14; Operating Temperature Min:-40C; Operating Temperature ;RoHS Compliant: Yes |
| LM5010AQ0MH/NOPB | 功能描述:直流/直流开关转换器 Hi Vltg 1A Step Down Switching Reg RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。