- 您现在的位置：买卖IC网 > PDF目录79953 > LM5045SQX (NATIONAL SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 540 kHz SWITCHING FREQ-MAX, QCC28 PDF资料下载
参数资料
| 型号： | LM5045SQX |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 540 kHz SWITCHING FREQ-MAX, QCC28 |
| 封装： | 5 X 5 MM, LLP-28 |
| 文件页数： | 18/28页 |
| 文件大小： | 610K |
| 代理商： | LM5045SQX |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
HICCUP MODE CURRENT LIMIT RESTART
The operation of the hiccup mode restart circuit is explained
in the Functional Description section. During a continuous
current limit condition, the RES pin is charged with 30A cur-
rent source. The restart delay time required to reach the 1.0V
threshold is given by:
This establishes the time allowed before the IC initiates a hic-
cup restart sequence. For example, if the C
RES=0.01F, the
time TCS as noted in Figure 20 below is 334s. Once the RES
pin reaches 1.0V, the 30A current source is turned-off and
a 10A current source is turned-on during the ramp up to 4V
and a 5A is turned on during the ramp down to 2V. The hic-
cup mode off-time is given by:
With a C
RES=0.01F, the hiccup time is 49ms. Once the hic-
cup time is finished, the RES pin is pulled-low and the SS pin
is released allowing a soft-start sequence to commence.
Once the SS pin reaches 1V, the PWM pulses will commence.
The hiccup mode provides a cool-down period for the power
converter in the event of a sustained overload condition there-
by lowering the average input current and temperature of the
power components during such an event.
PRINTED CIRCUIT BOARD LAYOUT
The LM5045 current sense and PWM comparators are very
fast and respond to short duration noise pulses. The compo-
nents at the CS, COMP, SLOPE, RAMP, SS, SSSR, RES,
UVLO, OVP, RD1, RD2, and RT pins should be physically
close as possible to the IC, thereby minimizing noise pickup
on the PC board trace inductance. Eliminating or minimizing
via’s in these critical connections are essential. Layout con-
sideration is critical for the current sense filter. If a current
sense transformer is used, both leads of the transformer sec-
ondary should be routed to the sense filter components and
to the IC pins. The ground side of the transformer should be
connected via a dedicated PC board trace to the AGND pin,
rather than through the ground plane. If the current sense cir-
cuit employs a sense resistor in the drive transistor source,
low inductance resistors should be used. In this case, all the
noise sensitive, low-current ground trace should be connect-
ed in common near the IC, and then a single connection made
to the power ground (sense resistor ground point).
The gate drive outputs of the LM5045 should have short, di-
rect paths to the power MOSFETs in order to minimize in-
ductance in the PC board. The boot-strap capacitors required
for the high side gate drivers should be located very close to
the IC and connected directly to the BST and HS pins. The
VCC and REF capacitors should also be placed close to their
respective pins with short trace inductance. Low ESR and
ESL ceramic capacitors are recommended for the boot-strap,
VCC and the REF capacitors. The two ground pins (AGND,
PGND) must be connected together directly underneath the
IC with a short, direct connection, to avoid jitter due to relative
ground bounce.
Application Circuit Example
The following schematic shows an example of a 100W full-
bridge converter controlled by LM5045. The operating input
voltage range is 36V to 75V, and the output voltage is 3.3V.
The output current capability is 30 Amps. The converter is
configured for current mode control with external slope com-
pensation. An auxiliary winding is used to raise the VCC
voltage to reduce the controller power dissipation.
30145416
FIGURE 20. Hiccup Mode Delay and Soft-Start Timing Diagram
25
www.national.com
LM5045
相关PDF资料 |
PDF描述 |
|---|---|
| LT1183CN | 1.25 A FLUORESCENT LIGHT CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDIP16 |
| LM385BMZ-1.2 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PBCY3 |
| LU100-12 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| L-12-OV-15 | SPECIALTY ANALOG CIRCUIT, MUFM2 |
| LS1501-7RD3TB1 | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM5045SQX/NOPB | 功能描述:IC PWM CTRLR FULL BRIDG 28LLP RoHS:是 类别:集成电路 (IC) >> PMIC - AC-DC 转换器，离线开关 系列:PowerWise® 标准包装:1 系列:FPS™ 输出隔离:隔离 频率范围:61kHz ~ 73kHz 输入电压:8 V ~ 26 V 输出电压:650V 功率（瓦特）:12W 工作温度:-40°C ~ 115°C 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-MDIP 包装:Digi-Reel® 其它名称:FSL206MRBNFSDKR |
| LM5046 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Input operating range: 36V to 75V Line UVLO (34V/32V on/off) |
| LM5046_1 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Input operating range: 36V to 75V Line UVLO (34V/32V on/off) |
| LM5046EVAL/NOPB | 功能描述:电源管理IC开发工具 LM5046 Eval Brd RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LM5046MH | 制造商:Texas Instruments 功能描述:CTLR, FULL BRIDGE, PWM, 28TSSOP 制造商:Texas Instruments 功能描述:CTLR, FULL BRIDGE, PWM, 28TSSOP; Input Voltage:100V; Supply Voltage Min:12.5V; Supply Voltage Max:30V; Digital IC Case Style:TSSOP; No. of Pins:28; Frequency:2MHz; Operating Temperature Min:-40C; Operating Temperature Max:125C; ;RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。