- 您现在的位置：买卖IC网 > PDF目录67756 > LM5117PMH (NATIONAL SEMICONDUCTOR CORP) SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PDSO20 PDF资料下载
参数资料
| 型号： | LM5117PMH |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, 530 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封装： | TSSOP-20 |
| 文件页数： | 6/32页 |
| 文件大小： | 844K |
| 代理商： | LM5117PMH |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Ramp Generator and Emulated
Current Sense
The ramp signal used in the pulse width modulator for tradi-
tional current mode control is typically derived directly from
the high-side switch current. This switch current corresponds
to the positive slope portion of the inductor current. Using this
signal for the PWM ramp simplifies the control loop transfer
function to a single pole response and provides inherent input
voltage feed-forward compensation.
The disadvantage of using the high-side switch current signal
for PWM control is the large leading edge spike due to circuit
parasitics that must be filtered or blanked. Minimum achiev-
able pulse width is limited by the filtering, blanking time and
propagation delay with a high-side current sensing scheme.
In the applications where the input voltage may be relatively
large in comparison to the output voltage, controlling small
pulse widths and duty cycles are necessary for regulation.
The LM5117 utilizes a unique ramp generator which does not
actually measure the high-side switch current but rather re-
constructs the signal. Representing or emulating the inductor
current provides a ramp signal to the PWM comparator that
is free of leading edge spikes and measurement or filtering
delays, while maintaining the advantages of traditional peak
current mode control.
The current reconstruction is comprised of two elements: a
sample-and-hold DC level and the emulated inductor current
ramp as shown in Figure 7. The sample-and-hold DC level is
derived from a measurement of the recirculating current flow-
ing through the current sense resistor. The voltage across the
sense resistor is sampled and held just prior to the onset of
the next conduction interval of the high-side switch. The cur-
rent sense amplifier with a gain of 10 and sample-and-hold
circuit provide the DC level of the reconstructed current signal
as shown in Figure 8.
30143216
FIGURE 7. Composition of Emulated Current Sense
Signal
30143213
FIGURE 8. RAMP Generator and Current Limit Circuit
The positive slope inductor current ramp is emulated by
C
RAMP connected between RAMP and AGND and RRAMP con-
nected between SW and RAMP. R
RAMP should not be con-
nected to VIN directly because the RAMP pin absolute
maximum voltage rating could be exceeded under high input
voltage conditions. C
RAMP is discharged by an internal switch
during the off-time and must be fully discharged during the
minimum off-time. This limits the ramp capacitor to be less
than 2nF. A good quality, thermally stable ceramic capacitor
is recommended for C
RAMP.
The selection of R
RAMP and CRAMP can be simplified by adopt-
ing a K factor, which is defined as:
(4)
Where A
S is the current sense amplifier gain which is normally
10. By choosing 1 as the K factor, the regulator removes any
error after one switching cycle and the design procedure is
simplified. See Application Information for detailed informa-
tion.
Error Amplifier and PWM
Comparator
The internal high-gain error amplifier generates an error sig-
nal proportional to the difference between the FB pin voltage
and the internal precision 0.8V reference. The output of error
amplifier is connected to the COMP pin allowing the user to
provide Type 2 loop compensation components, R
COMP,
C
COMP and optional CHF.
30143217
FIGURE 9. Feedback Configuration and PWM
Comparator
www.national.com
14
LM5117
相关PDF资料 |
PDF描述 |
|---|---|
| LM604CMX | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| LM604ACMX | SPECIALTY ANALOG CIRCUIT, PDSO20 |
| LM629M-6X | BRUSH DC MOTOR CONTROLLER, PDSO24 |
| LM629M-8X | BRUSH DC MOTOR CONTROLLER, PDSO24 |
| LM7005 | PLL FREQUENCY SYNTHESIZER, 35 MHz, PDIP24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM5117PMH/NOPB | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| LM5117PMH/NOPB | 制造商:Texas Instruments 功能描述:IC DC-DC CONV 750kHz TSSOP-20 制造商:Texas Instruments 功能描述:IC, DC-DC CONV, 750kHz, TSSOP-20 |
| LM5117PMHE/NOPB | 功能描述:DC/DC 开关控制器 Wide Input Range Sync Buck Cntlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| LM5117PMHX/NOPB | 功能描述:DC/DC 开关控制器 RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| LM5117PSQ/NOPB | 功能描述:DC/DC 开关控制器 Wide Input Range Sync Buck Cntlr RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
发布紧急采购，3分钟左右您将得到回复。