参数资料
型号: LM75BD,112
厂商: NXP Semiconductors
文件页数: 12/37页
文件大小: 520K
描述: IC TEMP SENSOR DIGITAL 8-SOIC
特色产品: Digital Temperature Sensor / Thermal Watchdog
标准包装: 100
功能: 温度监视系统(传感器),监视器
传感器类型: 内部
感应温度: -55°C ~ 125°C
精确度: ±3°C(最小值)
拓扑: ADC(三角积分型),比较器,振荡器,寄存器库
输出类型: 2 线串行,I²C?
输出警报:
输出风扇:
电源电压: 2.8 V ~ 5.5 V
工作温度: -55°C ~ 125°C
安装类型: 表面贴装
封装/外壳: 8-SOIC(0.154",3.90mm 宽)
供应商设备封装: 8-SO
包装: 管件
其它名称: 935285837112
LM75BD
LM75BD-ND
LM75B
All information provided in this document is subject to legal disclaimers.
?NXP B.V. 2014. All rights reserved.
Product data sheet
Rev. 5  22 January 2014
12 of 37
NXP Semiconductors
LM75B
Digital temperature sensor and thermal watchdog
7.7   OS fault queue
Fault queue is defined as the number of faults that must occur consecutively to activate
the OS output. It is provided to avoid false tripping due to noise. Because faults are
determined at the end of data conversions, fault queue is also defined as the number of
consecutive conversions returning a temperature trip. The value of fault queue is
selectable by programming the two bits B4 and B3 (OS_F_QUE[1:0]) in register Conf.
Notice that the programmed data and the fault queue value are not the same. Table 14
 
shows the one-to-one relationship between them. At power-up, fault queue data = 0 and
fault queue value = 1.
 
7.8   Shutdown mode
The device operation mode is selected by programming bit B0 (SHUTDOWN) of register
Conf. Setting bit SHUTDOWN to logic 1 will put the device into shutdown mode. Resetting
bit SHUTDOWN to logic 0 will return the device to normal mode.
In shutdown mode, the device draws a small current of approximately 1.0 mA and the
power dissipation is minimized; the temperature conversion stops, but the I
2
C-bus
interface remains active and register write/read operation can be performed. When the
shutdown is set, the OS output will be unchanged in comparator mode and reset in
interrupt mode.
7.9   Power-up default and power-on reset
The LM75B always powers-up in its default state with:
" Normal operation mode
"  OS comparator mode
"  T
th(ots)
 = 80 癈
"  T
hys
 = 75 癈
"  OS output active state is LOW
"  Pointer value is logic 00 (Temp)
When the power supply voltage is dropped below the device power-on reset level of
approximately 1.0 V (POR) for over 2 ms and then rises up again, the device will be reset
to its default condition as listed above.
Table 14.   Fault queue table
Fault queue data
Fault queue value
OS_F_QUE[1]
OS_F_QUE[0]
Decimal
0
0
1
0
1
2
1
0
4
1
1
6
相关PDF资料
PDF描述
LM75BIMX-5+ IC TEMP SENSOR WATCHDOG 8SOIC
LM92CIMX/NOPB IC SENSOR TEMP/THERM COMP 8-SOIC
LT1123CST#TRPBF IC REG CTRLR SGL 5V SOT223
LT1248IS#PBF IC PFC CTRLR AVERAGE CURR 16SOIC
LT1249IS8#PBF IC PFC CTRLR AVERAGE CURR 8SOIC
相关代理商/技术参数
参数描述
LM75BDP 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR DIGITAL 8-TSSOP 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8-TSSOP
LM75BDP,118 功能描述:板上安装温度传感器 I2C LOCAL +/- 20C TS DIGITAL TEMP SENSOR RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
LM75BDP,118-CUT TAPE 制造商:NXP 功能描述:LM75 Series Digital Temperature Sensor/Thermal Watchdog Surface Mount- TSSOP - 8
LM75BDP/DG,118 功能描述:板上安装温度传感器 DIGITAL TEMP SENSOR AND THERMAL WATCHDOG RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor
LM75BDP118 制造商:NXP Semiconductors 功能描述:DIGITAL TEMP SENSOR IC 11BIT +/-3C TS