- 您现在的位置：买卖IC网 > PDF目录178070 > LM75BIM-5/NOPB (NATIONAL SEMICONDUCTOR CORP) DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT PDF资料下载
参数资料
| 型号： | LM75BIM-5/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | Switch/Digital Output Temperature Sensor |
| 英文描述： | DIGITAL TEMP SENSOR-SERIAL, 9BIT(s), 3Cel, RECTANGULAR, SURFACE MOUNT |
| 封装： | 0.150 INCH, SOP-8 |
| 文件页数： | 7/18页 |
| 文件大小： | 474K |
| 代理商： | LM75BIM-5/NOPB |
2.0 Application Hints
To get the expected results when measuring temperature with
an integrated circuit temperature sensor like the LM75, it is
important to understand that the sensor measures its own die
temperature. For the LM75, the best thermal path between
the die and the outside world is through the LM75's pins. In
the MSOP-8 package for the LM75B and LM75C, the GND
pin is directly connected to the die, so the GND pin provides
the best thermal path. If the other pins are at different tem-
peratures (unlikely, but possible), they will affect the die tem-
perature, but not as strongly as the GND pin. In the SO-8
package, none of the pins is directly connected to the die, so
they will all contribute similarly to the die temperature. Be-
cause the pins represent a good thermal path to the LM75 die,
the LM75 will provide an accurate measurement of the tem-
perature of the printed circuit board on which it is mounted.
There is a less efficient thermal path between the plastic
package and the LM75 die. If the ambient air temperature is
significantly different from the printed circuit board tempera-
ture, it will have a small effect on the measured temperature.
In probe-type applications, the LM75 can be mounted inside
a sealed-end metal tube, and can then be dipped into a bath
or screwed into a threaded hole in a tank. As with any IC, the
LM75 and accompanying wiring and circuits must be kept in-
sulated and dry, to avoid leakage and corrosion. This is
especially true if the circuit may operate at cold temperatures
where condensation can occur. Printed-circuit coatings and
varnishes such as Humiseal and epoxy paints or dips are of-
ten used to insure that moisture cannot corrode the LM75 or
its connections.
2.1 DIGITAL NOISE ISSUES
The LM75A and LM75B feature an integrated low-pass filter
on both the SCL and the SDA digital lines to mitigate the ef-
fects of bus noise. Although this filtering makes the LM75A
and LM75B communication robust in noisy environments,
good layout practices are always recommended. Minimize
noise coupling by keeping digital traces away from switching
power supplies. Also, ensure that digital lines containing high-
speed data communications cross at right angles to the SDA
and SCL lines.
Excessive noise coupling into the SDA and SCL lines on the
LM75C—specifically noise with amplitude greater than
400 mV
pp (the LM75’s typical hysteresis), overshoot greater
than 300 mV above +V
s, and undershoot more than 300 mV
below GND—may prevent successful serial communication
with the LM75C. Serial bus no-acknowledge is the most com-
mon symptom, causing unnecessary traffic on the bus. The
layout procedures mentioned above apply also to the LM75C.
Although the serial bus maximum frequency of communica-
tion is only 400 kHz, care must be taken to ensure proper
termination within a system with long printed circuit board
traces or multiple parts on the bus. Resistance can be added
in series with the SDA and SCL lines to further help filter noise
and ringing. A 5 k
resistor should be placed in series with
the SCL line, placed as close as possible to the SCL pin on
the LM75C. This 5 k
resistor, with the 5 pF to 10 pF stray
capacitance of the LM75 provides a 6 MHz to 12 MHz low
pass filter, which is sufficient filtering in most cases.
3.0 Typical Applications
1265812
When using the two-wire interface: program O.S. for active high and connect O.S. directly to Q2's gate.
FIGURE 8. Simple Fan Controller, Interface Optional
15
www.national.com
LM75
相关PDF资料 |
PDF描述 |
|---|---|
| LM75 | 2-Wire Serial Temperature Sensor and Monitor |
| LM80CIMTX-32 | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM9637EVAL-KIT | LM9637 Monochrome CMOS Image Sensor VGA 68 FPS |
| LM9647EVAL-KIT | LM9647 Color CMOS Image Sensor VGA 68 FPS |
| LM99-1CIMM | 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM75BIMM-3 | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM75BIMM-3/NOPB | 功能描述:板上安装温度传感器 Digital Temp Sensor RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM75BIMM-3/NOPB | 制造商:Texas Instruments 功能描述:Temperature Sensor IC |
| LM75BIMM-3+ | 功能描述:板上安装温度传感器 2-Wire Digital Temp Snsr & Thrml Wtchdog RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
| LM75BIMM-3+T | 功能描述:板上安装温度传感器 2-Wire Digital Temp Snsr & Thrml Wtchdog RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。