- 您现在的位置：买卖IC网 > PDF目录17116 > LM89-1EVAL (National Semiconductor)BOARD EVALUATION LM89-1 PDF资料下载
参数资料
| 型号： | LM89-1EVAL |
| 厂商： | National Semiconductor |
| 文件页数： | 13/32页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION LM89-1 |
| 标准包装： | 1 |
| 传感器类型： | 温度 |
| 传感范围： | 0°C ~ 125°C |
| 接口： | SMBus（2 线/I²C） |
| 灵敏度： | ±1°C |
| 电源电压： | 3 V ~ 3.6 V |
| 嵌入式： | 否 |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | LM89-1 |
| 相关产品： | LM89-1CIMX-ND - IC TEMP SENSOR DGTL 8-SOIC LM89-1CIMM/NOPBTR-ND - IC TEMP SENSOR DGTL 8-MSOP LM89-1CIMMX/NOPBTR-ND - IC TEMP SENSOR DGTL 8-MSOP LM89-1CIM-ND - IC TEMP SENSOR DGTL 8-SOIC |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
Temperature
Digital Output
SNIS128C – AUGUST 2002 – REVISED MARCH 2013
Binary
Hex
+125°C
+25°C
+1°C
0°C
? 1°C
? 25°C
? 55°C
0111 1101
0001 1001
0000 0001
0000 0000
1111 1111
1110 0111
1100 1001
7Dh
19h
01h
00h
FFh
E7h
C9h
OPEN-DRAIN OUTPUTS
The SMBData, ALERT and T_CRIT_A outputs are open-drain outputs and do not have internal pull-ups. A “high”
level will not be observed on these pins until pull-up current is provided by some external source, typically a pull-
up resistor. Choice of resistor value depends on many system factors but, in general, the pull-up resistor should
be as large as possible. This will minimize any internal temperature reading errors due to internal heating of the
LM89. The maximum resistance of the pull-up to provide a 2.1V high level, based on LM89 specification for High
Level Output Current with the supply voltage at 3.0V, is 82k Ω (5%) or 88.7k Ω (1%).
DIODE FAULT DETECTION
The LM89 is equipped with operational circuitry designed to detect fault conditions concerning the remote diode.
In the event that the D+ pin is detected as shorted to V DD or floating, the Remote Temperature High Byte (RTHB)
register is loaded with +127°C, the Remote Temperature Low Byte (RTLB) register is loaded with 0, and the
OPEN bit (D2) in the status registe r is set. As a result, if the Remote T_CRIT setpoint register (RCS) is set to a
value less than +127°C the ALERT and T_Crit output pins will be pulled low, if the Alert Mask and T_Crit Mask
are disabled. If the Remote HIGH Setpoint High Byte Register (RHSHB) is set to a value less than +127°C then
ALERT will be pulled low, if the Alert Mask is disabled. The OPEN bit itself will not trigger and ALERT.
In the event that the D+ pin is shorted to ground or D ? , the Remote Temperature High Byte (RTHB) register is
loaded with ? 128°C (1000 0000) and the OPEN bit (D2) in the status register will not be set. Since operating the
LM89 at ? 128°C is beyond it's operational limits, this temperature reading represents this shorted fault condition.
If the value in the Remote Low Setpoint High Byte Register (RLSHB) is more than ? 128°C and the Alert Mask is
disabled, ALERT will be pulled low.
Remote diode temperature sensors that have been previously released and are competitive with the LM89 output
a code of 0°C if the external diode is short-circuited. This change is an improvement that allows a reading of 0°C
to be truly interpreted as a genuine 0°C reading and not a fault condition.
COMMUNICATING WITH THE LM89
The data registers in the LM89 are selected by the Command Register. At power-up the Command Register is
set to “00”, the location for the Read Local Temperature Register. The Command Register latches the last
location it was set to. Each data register in the LM89 falls into one of four types of user accessibility:
1. Read only
2. Write only
3. Read/Write same address
4. Read/Write different address
A Write to the LM89 will always include the address byte and the command byte. A write to any register requires
one data byte.
Reading the LM89 can take place either of two ways:
1. If the location latched in the Command Register is correct (most of the time it is expected that the Command
Register will point to one of the Read Temperature Registers because that will be the data most frequently
read from the LM89), then the read can simply consist of an address byte, followed by retrieving the data
byte.
2. If the Command Register needs to be set, then an address byte, command byte, repeat start, and another
address byte will accomplish a read.
Copyright ? 2002–2013, Texas Instruments Incorporated
Product Folder Links: LM89
13
相关PDF资料 |
PDF描述 |
|---|---|
| KITMPR083EVM | KIT EVAL 8POSITION ROTARY TOUCH |
| RCC12DREN-S734 | CONN EDGECARD 24POS .100 EYELET |
| VE-J7P-EZ | CONVERTER MOD DC/DC 13.8V 25W |
| GBM28DSEN | CONN EDGECARD 56POS .156 EYELET |
| ADR06WARZ-RL | IC VREF SERIES PREC 3V 8SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LM8942 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LM8972 | 制造商:未知厂家 制造商全称:未知厂家 功能描述: |
| LM89CIM | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LM89CIM/NOPB | 功能描述:IC TEMP SENSOR DGTL 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 热管理 系列:- 标准包装:1 系列:- 功能:温度监控系统（传感器） 传感器类型:内部和外部 感应温度:-40°C ~ 125°C，外部传感器 精确度:±2.5°C 本地（最大值），±5°C 远程（最大值） 拓扑:ADC，比较器，寄存器库 输出类型:2 线 SMBus? 输出警报:无 输出风扇:无 电源电压:2.7 V ~ 5.5 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:SOT-23-8 供应商设备封装:SOT-23-8 包装:Digi-Reel® 其它名称:296-22675-6 |
| LM89CIMM | 功能描述:板上安装温度传感器 RoHS:否 制造商:Omron Electronics 输出类型:Digital 配置: 准确性:+/- 1.5 C, +/- 3 C 温度阈值: 数字输出 - 总线接口:2-Wire, I2C, SMBus 电源电压-最大:5.5 V 电源电压-最小:4.5 V 最大工作温度:+ 50 C 最小工作温度:0 C 关闭: 安装风格: 封装 / 箱体: 设备功能:Temperature and Humidity Sensor |
发布紧急采购，3分钟左右您将得到回复。