- 您现在的位置：买卖IC网 > PDF目录44573 > LMP90078MHX/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY ANALOG CIRCUIT, PDSO28 PDF资料下载
参数资料
| 型号： | LMP90078MHX/NOPB |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| 封装： | LEAD FREE, PLASTIC, MO-153, TSSOP-28 |
| 文件页数： | 28/62页 |
| 文件大小： | 1721K |
| 代理商： | LMP90078MHX/NOPB |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页
30169732
FIGURE 22. DrdybCase1 Connection Diagram
As shown in Figure 22, the drdyb signal and SDO can be
multiplexed on the same pin as their functions are mostly
complementary. In fact, this is the default mode for the
SDO/DRDYB pin.
Figure 23 shows a timing protocol for DrdybCase1. In this
case, start by asserting CSB first to monitor a drdyb assertion.
When the drdyb signal asserts, begin writing the Instruction
Bytes (INST1, UAB, INST2) to read from or write to registers.
Note that INST1 and UAB are omitted from the figure below
because this transaction is only required if a new UAB needs
to be implemented.
While the CSB is asserted, DRDYB is driving the
SDO/DRDYB pin unless the device is reading data, in which
case, SDO will be driving the pin. If CSB is deasserted, then
the SDO/DRDYB pin is High-Z.
30169701
FIGURE 23. Timing Protocol for DrdybCase1
DrdybCase2:
Combining
SDO/DRDYB
with
SDO_DRDYB_DRIVER = 0x03
SDO/DRDYB can be made independent of CSB by setting
SDO_DRDYB_DRIVER = 0x03 in the SPI Handshake Control
register. In this case, DRDYB will drive the pin unless the de-
vice is reading data, independent of the state of CSB. SDO
will drive the pin when CSB is asserted and the device is
reading data.
With this scheme, one can use SDO/DRDYB as a true inter-
rupt source, independent of the state of CSB. But this scheme
can only be used when the LMP900xx is the only device con-
nected to the master's SPI bus because the SDO/DRDYB pin
will be DRDYB even when CSB is deasserted.
The timing protocol for this case can be seen in Figure 24.
When drdyb asserts, assert CSB to start the SPI transaction
and begin writing the Instruction Bytes (INST1, UAB, INST2)
to read from or write to registers.
www.national.com
34
LMP90080/LMP90079/LMP90078/LMP90077
相关PDF资料 |
PDF描述 |
|---|---|
| LMP90078MHE/NOPB | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LMP90079MHX/NOPB | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LMP90080MHE/NOPB | SPECIALTY ANALOG CIRCUIT, PDSO28 |
| LMV431ACMWC | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, UUC |
| LMV431IMDC | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, UUC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMP90079 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Sensor AFE System: Multi-Channel, Low-Power 16-Bit |
| LMP90079MH/NOPB | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| LMP90079MHE/NOPB | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| LMP90079MHX/NOPB | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| LMP90080 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Sensor AFE System: Multi-Channel, Low-Power 16-Bit |
发布紧急采购，3分钟左右您将得到回复。