- 您现在的位置：买卖IC网 > PDF目录79981 > LMX2575HVMX-12 (NATIONAL SEMICONDUCTOR CORP) 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDSO24 PDF资料下载
参数资料
| 型号： | LMX2575HVMX-12 |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封装： | SMT-24 |
| 文件页数： | 8/30页 |
| 文件大小： | 676K |
| 代理商： | LMX2575HVMX-12 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
Application Hints
INPUT CAPACITOR (C
IN)
To maintain stability, the regulator input pin must be by-
passed with at least a 47 F electrolytic capacitor. The ca-
pacitor’s leads must be kept short, and located near the
regulator.
If the operating temperature range includes temperatures
below 25C, the input capacitor value may need to be
larger. With most electrolytic capacitors, the capacitance
value decreases and the ESR increases with lower tempera-
tures and age. Paralleling a ceramic or solid tantalum ca-
pacitor will increase the regulator stability at cold tempera-
tures. For maximum capacitor operating lifetime, the
capacitor’s RMS ripple current rating should be greater than
INDUCTOR SELECTION
All switching regulators have two basic modes of operation:
continuous and discontinuous. The difference between the
two types relates to the inductor current, whether it is flowing
continuously, or if it drops to zero for a period of time in the
normal switching cycle. Each mode has distinctively different
operating characteristics, which can affect the regulator per-
formance and requirements.
The LM2575 (or any of the Simple Switcher family) can be
used for both continuous and discontinuous modes of opera-
tion.
The inductor value selection guides in
Figure 3 through Fig-
ure 7 were designed for buck regulator designs of the con-
tinuous inductor current type. When using inductor values
shown in the inductor selection guide, the peak-to-peak in-
ductor ripple current will be approximately 20% to 30% of the
maximum DC current. With relatively heavy load currents,
the circuit operates in the continuous mode (inductor current
always flowing), but under light load conditions, the circuit
will be forced to the discontinuous mode (inductor current
falls to zero for a period of time). This discontinuous mode of
operation is perfectly acceptable. For light loads (less than
approximately 200 mA) it may be desirable to operate the
regulator in the discontinuous mode, primarily because of
the lower inductor values required for the discontinuous
mode.
The selection guide chooses inductor values suitable for
continuous mode operation, but if the inductor value chosen
is prohibitively high, the designer should investigate the pos-
sibility of discontinuous operation. The computer design soft-
ware
Switchers Made Simple will provide all component
values for discontinuous (as well as continuous) mode of op-
eration.
Inductors are available in different styles such as pot core,
toriod, E-frame, bobbin core, etc., as well as different core
materials, such as ferrites and powdered iron. The least ex-
pensive, the bobbin core type, consists of wire wrapped on a
ferrite rod core. This type of construction makes for an inex-
pensive inductor, but since the magnetic flux is not com-
pletely contained within the core, it generates more electro-
magnetic interference (EMI). This EMI can cause problems
in sensitive circuits, or can give incorrect scope readings be-
cause of induced voltages in the scope probe.
The inductors listed in the selection chart include ferrite pot
core construction for AIE, powdered iron toroid for Pulse En-
gineering, and ferrite bobbin core for Renco.
An inductor should not be operated beyond its maximum
rated current because it may saturate. When an inductor be-
gins to saturate, the inductance decreases rapidly and the
inductor begins to look mainly resistive (the DC resistance of
the winding). This will cause the switch current to rise very
rapidly. Different inductor types have different saturation
characteristics, and this should be kept in mind when select-
ing an inductor.
The inductor manufacturer’s data sheets include current and
energy limits to avoid inductor saturation.
INDUCTOR RIPPLE CURRENT
When the switcher is operating in the continuous mode, the
inductor current waveform ranges from a triangular to a saw-
tooth type of waveform (depending on the input voltage). For
a given input voltage and output voltage, the peak-to-peak
amplitude of this inductor current waveform remains con-
stant. As the load current rises or falls, the entire sawtooth
current waveform also rises or falls. The average DC value
of this waveform is equal to the DC load current (in the buck
regulator configuration).
If the load current drops to a low enough level, the bottom of
the sawtooth current waveform will reach zero, and the
switcher will change to a discontinuous mode of operation.
This is a perfectly acceptable mode of operation. Any buck
switching regulator (no matter how large the inductor value
is) will be forced to run discontinuous if the load current is
light enough.
OUTPUT CAPACITOR
An output capacitor is required to filter the output voltage and
is needed for loop stability. The capacitor should be located
near the LM2575 using short pc board traces. Standard alu-
minum electrolytics are usually adequate, but low ESR types
are recommended for low output ripple voltage and good
stability. The ESR of a capacitor depends on many factors,
some which are: the value, the voltage rating, physical size
and the type of construction. In general, low value or low
voltage (less than 12V) electrolytic capacitors usually have
higher ESR numbers.
The amount of output ripple voltage is primarily a function of
the ESR (Equivalent Series Resistance) of the output ca-
pacitor and the amplitude of the inductor ripple current
(
I
IND). See the section on inductor ripple current in Applica-
tion Hints.
The lower capacitor values (220 F–680 F) will allow typi-
cally 50 mV to 150 mV of output ripple voltage, while
larger-value capacitors will reduce the ripple to approxi-
mately 20 mV to 50 mV.
Output Ripple Voltage = (
I
IND) (ESR of COUT)
To further reduce the output ripple voltage, several standard
electrolytic capacitors may be paralleled, or a higher-grade
capacitor may be used. Such capacitors are often called
“high-frequency,” “low-inductance,” or “low-ESR.” These will
reduce the output ripple to 10 mV or 20 mV. However, when
operating in the continuous mode, reducing the ESR below
0.05
can cause instability in the regulator.
www.national.com
16
相关PDF资料 |
PDF描述 |
|---|---|
| LS1001-7EPD2TB1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1001-7EPD9B1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1001-7PD4 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1001-7PT | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
| LS1001-9RD6TB1 | 1-OUTPUT 100 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LMX2581 | 制造商:TI 制造商全称:Texas Instruments 功能描述:LMX2581 Wideband Frequency Synthesizer with Integrated VCO |
| LMX2581EVAL/NOPB | 功能描述:时钟和定时器开发工具 LMX2581 EVAL MOD RoHS:否 制造商:Texas Instruments 产品:Evaluation Modules 类型:Clock Conditioners 工具用于评估:LMK04100B 频率:122.8 MHz 工作电源电压:3.3 V |
| LMX2581EVM | 功能描述:LMX2581 - Timing, Frequency Synthesizer Evaluation Board 制造商:texas instruments 系列:- 零件状态:有效 主要用途:计时，频率合成器 嵌入式:- 使用的 IC/零件:LMX2581 主要属性:带 VCO 的单路分数-N PLL 辅助属性:- 所含物品:板 标准包装:1 |
| LMX2581SQ | 制造商:TI 制造商全称:Texas Instruments 功能描述:LMX2581 Wideband Frequency Synthesizer with Integrated VCO |
| LMX2581SQ/NOPB | 制造商:Texas Instruments 功能描述:IC FREQ SYNTHESIZER VCO 32WQFN 制造商:Texas Instruments 功能描述:CLOCK GENERATION/OTHER IC |
发布紧急采购，3分钟左右您将得到回复。