- 您现在的位置：买卖IC网 > PDF目录79808 > LP3918TLX-I (NATIONAL SEMICONDUCTOR CORP) 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA25 PDF资料下载
参数资料
| 型号： | LP3918TLX-I |
| 厂商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分类： | 电源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PBGA25 |
| 封装： | 2.50 X 2.50 MM, MICRO, SMD-25 |
| 文件页数： | 16/30页 |
| 文件大小： | 1271K |
| 代理商： | LP3918TLX-I |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页
IMON CHARGE CURRENT MONITOR
Charge current is monitored within the charger section and a
proportional voltage representation of the charge current is
presented at the IMON output pin. The output voltage rela-
tionship to the actual charge current is represented in the
following graph and by the equation:
V
IMON(mV) = (2.47 x ICHG)(mA)
20211611
FIGURE 4. IMON Voltage vs Charge Current
Note that this function is not available if there is no input at
CHG_IN or if the charger is off due to the input at CHG_IN
being outwith the operating voltage range.
LDO Information
OPERATIONAL INFORMATION
The LP3918 has 7 LDO's of which 3 are enabled by default,
LDO's 1,2 and 3 are powered up during the power up se-
quence. LDO4, 5 and 6 are separately, externally enabled
and will follow LDO2 in start up if their respective enable pin
is pulled high. LDO2, LDO3 and LDO7 can be enabled/dis-
abled via the serial interface.
LDO2 must remain in regulation otherwise the device will
power down. While LDO1 is enabled this must also be in reg-
ulation for the device to remain powered. If LDO1 is disabled
via I2C interface the device will not shut down.
INPUT VOLTAGES
There are two input voltage pins used to power the 7LDO's
on the LP3918. V
IN2is the supply for LDO3, LDO4, LDO5,
LDO6 and LDO7. V
IN1is the supply for LDO1 and LDO2.
These input voltages should be tied to the Batt pin in the
application.
PROGRAMMING INFORMATION
Enable via Serial Interface
TABLE 18. Register Address 8h'00: OP_EN
BIT
NAME
FUNCTION
0
LDO1_EN
Bit set to '0' - LDO disabled
Bit set to '1' - LDO enabled
2
LDO3_EN
3
LDO7_EN
Note that the default setting for this Register is [0000 0101].
This shows that LDO1 and 3 are enabled by default whereas
LDO7 is not enabled by default on start up.
LDO OUTPUT PROGRAMMING
TABLE 19.
Regi
ster
Add
(hex)
NAME
Data Range
(hex)
Output Voltage
01
LDO1PGM
O/P
03 - 0F
1.5V to 3.3V
(def. 1.8V)
02
LDO2PGM
O/P
00 - 0F
2.5V to 3.3V
(def 3.0V)
03
LDO3PGM
O/P
05 - 0C
2.7V to 3.05V
(def 3.0V)
04
LDO4PGM
O/P
00 - 0F
1.5V to 3.3V
(def 3.0V)
05
LDO5PGM
O/P
05 - 0C
2.7V to 3.05V
(def 3.0V)
06
LDO6PGM
O/P
05 - 0C
2.7V to 3.05V
(def 3.0V)
07
LDO7PGM
O/P
00 - 0F
1.5V to 3.3V
(def 3.0V)
See Table 2 for full programmable range of values.
EXTERNAL CAPACITORS
The Low Drop Out Linear Voltage regulators on the LP3918
require external capacitors to ensure stable outputs. The
LDO's on the LP3918 are specifically designed to use small
surface mount ceramic capacitors which require minimum
board space. These capacitors must be correctly selected for
good performance
INPUT CAPACITOR
Input capacitors are required for correct operation. It is rec-
ommended that a 10F capacitor be connected between
each of the voltage input pins and ground (this capacitance
value may be increased without limit). This capacitor must be
located a distance of not more than 1cm from the input pin
and returned to a clean analogue ground. A ceramic capacitor
is recommended although a good quality tantalum or film ca-
pacitor may be used at the input.
Important:
Tantalum capacitors can suffer catastrophic fail-
ures due to surge current when connected to a low-
impedance source of power (like a battery or a very large
capacitor). If a tantalum capacitor is used at the input, it must
be guaranteed by the manufacturer to have surge current rat-
ing sufficent for the application. There are no requirements for
the ESR (Equivalent Series Resistance) on the input capaci-
tor, but tolerance and temparature coefficient must be con-
sidered when selecting the capacitor to ensure the capaci-
tance will remain within its operational range over the entire
operating temperature range and conditions.
Output Capacitor
Correct selection of the output capacitor is critical to ensure
stable operation in the intended application.The output ca-
pacitor must meet all the requirements specified in the rec-
ommended capacitor table over all conditions in the applica-
tion. These conditions include DC-bias, frequency and
temperature. Unstable operation will result if the capacitance
23
www.national.com
LP3918
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6102HVCMS8#TR | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LSM-3.3/16-W3-C | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LMX2336UTM/NOPB | PLL FREQUENCY SYNTHESIZER, 2000 MHz, PDSO20 |
| LTC1530IS8-1.9#PBF | SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO8 |
| LK2540-7ERDDTB1 | 2-OUTPUT 150 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LP3918TLX-L | 制造商:NSC 制造商全称:National Semiconductor 功能描述:Battery Charge Management and Regulator Unit |
| LP3919 | 制造商:NSC 制造商全称:National Semiconductor 功能描述:CDMA Power Management Unit |
| LP3919RL-A/NOPB | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| LP3919RL-B/NOPB | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| LP3919RL-C/NOPB | 功能描述:PMIC 解决方案 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。